Quantcast
Jump to content


Radiator Temp Sensor

venery99

By venery99
in Joyner UTV SxS Forum

 Share

Recommended Posts

venery99 Newbie

venery99

Posted
Posted

Does any one know of an aftermarket temperature sensor for the radiator in the Joyner Trooper? I think my sensor has failed open because the radiator fan is always on high from when I first start it up. I replace the relay thinking that is was stuck open, but that didn't help.

Kinarfi Veteran

Kinarfi

Posted
Posted

Does any one know of an aftermarket temperature sensor for the radiator in the Joyner Trooper? I think my sensor has failed open because the radiator fan is always on high from when I first start it up. I replace the relay thinking that is was stuck open, but that didn't help.

Not sure, well pretty sure, the fan runs full speed all the time. It runs during the start up and once the engine is running, it runs. Only has one speed. go to parts and piece and find the schematic and download it.

Kinarfi

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • BWF
      Landmaster LM200 Will Not Start
      By BWF
      I have a 2011 or so Landmaster LM200.  I cannot get it to start.  I turn the key and nothing happens.  The brake switch seems to be working, the ignition switch works.  The Coil is new the Voltage Regulator is new and the starter relay is new.
       
      I can connect the terminals on the starter relay and it starts right up and runs fine.  I just can't get it to start by turning the key.
       
      I am having a bit of trouble bleeding the brakes, not much fluid comes out at the calipers when I am pumping the brakes, though that an air bubble near the brake switch might make it not sense that the brake pedal is depressed.
       
      I am at a loss, please help!
       
      Brad
    • rdc
      Looking for a left rear shaft carrier (just the carrier) for a 2007 Joyner 1100 sand viper
      By rdc
      Hope I posted this in the right place. Looking for the left side shaft carrier where the rear bearings go for an 1100cc sand viper, I understand an 800 cc carrier will also work. I need the old style two bearing with the spacer in the middle, the new style with just the one wide bearing wont work. If anybody has one I'll buy it right away. my email is [email protected]
    • Garjess
      RTV 1140 Starter Relay
      By Garjess
      My rtv 1140 won't turn over.  I've jumped the neutral switch, and the brake switch, and checked the ignition switch. I'm not getting any power to the trigger wire on the starter solenoid.  It starts fine with the key on and putting power to the trigger wire on the solonoid.
      Does a 2010 RTV 1140 cpx have a starter relay? 
      Does anyone have a wiring diagram?
    • 180gtr
      Parting out Joyner Sand Viper 1100
      By 180gtr
      Parting out a rolled Sand viper 1100. I will list some of the parts I have, otherwise ask me if there is something specific you are looking for. I am selling everything I have for $800. I am located near Glenwood Springs CO.
      SOLD ITEMS, I do not have these items.
      Wheels
      Tires
      Engine
      Transmission
      Axles
      Shocks
      Control Arms
      Things I have....These all came off of the running engine. I have video of it running if anyone needs to verify that.
      Throttle Body $90
      Starter $150
      Alternator $150
      Fuel rail, injectors, fpr $100
      fuel pump $70
      Map Sensor $50
      Full set of Guages $150
      Exhaust w cat, O2 SOLD
      Ignition Coil - SOLD
      Wiring harness and ecu SOLD
      Radiator, shroud, elec fan, overflow tank $200
      Fuel tank w sender $150 Has dent at base of fuel neck, no leaks
      I have a box full of misc bolts, nuts, etc.
      I will sell the Chassis or Frame alone for $200. The chassis is in pretty good shape, needs some cage repair and 2 areas straightened where control arms mount. If anyone had an automotive frame machine it would take a few hours.
      That would include....
      Brake calipers, lines, pedal, master cyl, E brake assy,
      Steering shaft, wheel
      Ignition switch, key
      Light bar frame, 2 lights
      misc hardware, spindles
      2 hubs, rotors
      Engine mounts
      Throttle pedal, cables
      Shifter, cables
      Clutch master, pedal
      I am sure I am forgetting something.
      I am parting this out of ebay right now, I just picked up another project and could use the room. No I will not take less than $700 for all of it or $200 for the frame. I do not need to sell it, I will make far more parting it out but would like the extra space in the garage.
      If interested I also have an 07 1000rr engine setup I would sell with the buggy for $650.
      Thanks!
















    • Jody Deville
      Joyner 800 Renegade rear axles
      By Jody Deville
      I’m looking to best place to buy replacement axles for the rear in my buggy. Both axles are bad. Where is the best place to find them?

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...