Quantcast
Jump to content


Fuel Lines

ricksrb

By ricksrb
in Joyner UTV SxS Forum

 Share

Recommended Posts

ricksrb Mentor

ricksrb

Posted
Posted

Was out at Glamis North KOA this past weekend and on the way back from the Bat Caves after dark Saturday i started smelling gas.Got out and found a hole in my fuel line before the filter(mine is located after the pump below the regulator). Luckaly the hole was aimed perfectly out the drivers side towards the rear wheel and not back towards the engine.I had plently of slack in the line so i was able to just cut off the section with the hole and re-connect the line to the filter.This is not the stock fuel line, i replaced with fuel line purchased from auto zone about two years ago.Will be going in and replaceing all again this week.I know we have alot of pressure on the lines but should they not last longer? As you all know i dont get out that much so its not like i have tons of miles and hours running on it. Not from the weather either.Mine is always garaged.

Guest Lenny

Guest Lenny

Posted
Posted

I think they make 2 different pressure lines for EFI fuel systems. Be sure you use the higher pressure lines and don't use typical hose clamps but clamps that are specifically for injection lines. Keep the hoses secure so they don't move around and abrade against something. Hoses sould last a long time. Stailness lines are expensive but the best. Glad you didn't have a fire.

Lenny

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Fmaxiron
      Honda Pioneer 1000-6 back windshield or screen.
      By Fmaxiron
      I just purchased a 2023 Honda Pioneer a couple of weeks ago and had the hard roof and a front Honda Pioneer windshield installed at the shop before taking ownership. As things are drying up here in NC, the grass and dust are beginning to fly right through the back of the cab while driving. I was wondering if anyone has any good recommendations on rear windshields, dust panels, or mesh screens to help stop this?
      Thanks a lot!
    • Kierobi
      MSU 500 Fuel Pump Ground
      By Kierobi
      Have a MSU 500 that we got from my wife's uncle a while back. We've had it running and hauling around the property but it stopped a few months ago after what I thought was running out of gas and I'm just getting to looking into it. 
      Had fuel to the injector but nothing coming out the injector so swapped with new injector and installed inline filter in the supply hose from fuel pump. Tried again and still nothing but noticed this time that I can't hear the fuel pump priming. 
      Pulled off the electrical connection and I'm getting 12V to the fuel pump but it won't run. Put it on a test bench and got it to run so put test lamp between +ve and -ve terminals on the connector and nothing. Checked against the passenger seat securing post and get a light. 
      Tried chasing the wire back and think that the ground is through the ECU but not 100% sure. Can someone confirm for me? And if it is through the ECU, is the ECU just grounded against the frame or is it wired through to the battery?
      Thanks in advance and hope this all make sense!
    • Butch
      2023 Hisun Axis 700 fuel problem
      By Butch
      I have a AXIS 700 EFI Fuel pump pressure stays at 40 psi and when return line is blocked the pressure goes to 60 psi. and wll only run with return line closed. 
    • Jeff freeman
      Utv wont start and broken fuel injection wire
      By Jeff freeman
      I have a Coleman 550.  Was having problems to start with where it would start and then shut off after a couple tries. It would take off and be good. It then got to a point where it would not start at all. I replaced the fuel injection twice the second time I replaced it I noticed a mouse or something had chewed one of the wires that connect the electrical to the fuel injector. . So two-part question first does anybody have a part number for that wire harness?  Second, any other ideas after I fix the wire harness permanently on what could keep it from starting I have gas flow up to the fuel injector.


    • Eman85
      Fuel injector replacement Massimo 500
      By Eman85
      Pulled fuel injector to see if I could clean it or if it's stuck open. Had a slide on clip that was really tough to get off. Don't see how the clip is supposed to lock into the plastic part that the injector slides into. Any videos or pics of injector replacement? 

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...