Quantcast
Jump to content


Renegade ECM questions!

goindeep

By goindeep
in Joyner UTV SxS Forum

 Share

Recommended Posts

goindeep Enthusiast

goindeep

Posted
Posted

OK fellow Joyner people! I have a Renegade R4 in the shop right now. The man brought it to me as a "no start"... he said he went trail riding and got it stuck very bad, he left it overnight. The next morning went to get it and it wouldn't start.. he drug it home and somehow came to the conclusion it needed a new ecm... he gets a new one hooked it up and still no start... this is when I get it.. the ecm is laying in the floor and the two ground wires are not hooked up.. I ground the two wires and boom it starts up.. but only running on two cylinders. From what wire diagrams I can find the trooper has two coil drivers and the renegade has three. I have checked the coil and all the wires and all is good. I am not getting pulse from the ecm for the third coil... the old ecm cover was sitting in the floor so I compared the numbers, totally different! Called the place he ordered the ecm from and they are telling my the old number superseded to the new one I have. I checked the ecm on my trooper and the numbers match perfectly. So what I am saying is the new ecm they sent is a match for a trooper ecm... are they the same?

Thanks for any help!

Josh

post-1523-0-37749600-1360001152_thumb.jpg

post-1523-0-32593600-1360001363_thumb.jpg

goindeep Enthusiast

goindeep

Posted
  • Author
Posted

OK fellow Joyner people! I have a Renegade R4 in the shop right now. The man brought it to me as a "no start"... he said he went trail riding and got it stuck very bad, he left it overnight. The next morning went to get it and it wouldn't start.. he drug it home and somehow came to the conclusion it needed a new ecm... he gets a new one hooked it up and still no start... this is when I get it.. the ecm is laying in the floor and the two ground wires are not hooked up.. I ground the two wires and boom it starts up.. but only running on two cylinders. From what wire diagrams I can find the trooper has two coil drivers and the renegade has three. I have checked the coil and all the wires and all is good. I am not getting pulse from the ecm for the third coil... the old ecm cover was sitting in the floor so I compared the numbers, totally different! Called the place he ordered the ecm from and they are telling my the old number superseded to the new one I have. I checked the ecm on my trooper and the numbers match perfectly. So what I am saying is the new ecm they sent is a match for a trooper ecm... are they the same?

Thanks for any help!

Josh

Guest Lenny

Guest Lenny

Posted
Posted

If the numbers are the same, they are for the Trooper and that would explain the running incorrectly. Otherwise, the ECU looks for information from the tach and cam positon sensor to initiate spark. You might check there for a bad connection. Make sure your grounds are solid to the engine and ground the exterior of the ECU.

Lenny

plumber Proficient

plumber

Posted
Posted

#2 S11-3605010TA R2/R4 800 372ECU 1 561.35 #2 S11-3605010JA Trooper ECU 1 709.10

I would say yes they are different the last two number are different and the price are different

  • 2 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Popular Now

  • Similar Topics

    • rdc
      Looking for the left side shaft carrier where the rear bearings go for a 2014 1100cc sand viper, I understand an 800 cc carrier will also work.
      By rdc
      I posted this before , but I had the year wrong. The part I need is for a 2014, I don't know what all years will work, but I need the 2 bearing style with the spacer in the middle. It looks like this pic. If anyone has one I'll buy it rite away. my email is [email protected]. Thanks, RC

    • BWF
      Landmaster LM200 Will Not Start
      By BWF
      I have a 2011 or so Landmaster LM200.  I cannot get it to start.  I turn the key and nothing happens.  The brake switch seems to be working, the ignition switch works.  The Coil is new the Voltage Regulator is new and the starter relay is new.
       
      I can connect the terminals on the starter relay and it starts right up and runs fine.  I just can't get it to start by turning the key.
       
      I am having a bit of trouble bleeding the brakes, not much fluid comes out at the calipers when I am pumping the brakes, though that an air bubble near the brake switch might make it not sense that the brake pedal is depressed.
       
      I am at a loss, please help!
       
      Brad
    • rdc
      Looking for a left rear shaft carrier (just the carrier) for a 2007 Joyner 1100 sand viper
      By rdc
      Hope I posted this in the right place. Looking for the left side shaft carrier where the rear bearings go for an 1100cc sand viper, I understand an 800 cc carrier will also work. I need the old style two bearing with the spacer in the middle, the new style with just the one wide bearing wont work. If anybody has one I'll buy it right away. my email is [email protected]
    • 180gtr
      Parting out Joyner Sand Viper 1100
      By 180gtr
      Parting out a rolled Sand viper 1100. I will list some of the parts I have, otherwise ask me if there is something specific you are looking for. I am selling everything I have for $800. I am located near Glenwood Springs CO.
      SOLD ITEMS, I do not have these items.
      Wheels
      Tires
      Engine
      Transmission
      Axles
      Shocks
      Control Arms
      Things I have....These all came off of the running engine. I have video of it running if anyone needs to verify that.
      Throttle Body $90
      Starter $150
      Alternator $150
      Fuel rail, injectors, fpr $100
      fuel pump $70
      Map Sensor $50
      Full set of Guages $150
      Exhaust w cat, O2 SOLD
      Ignition Coil - SOLD
      Wiring harness and ecu SOLD
      Radiator, shroud, elec fan, overflow tank $200
      Fuel tank w sender $150 Has dent at base of fuel neck, no leaks
      I have a box full of misc bolts, nuts, etc.
      I will sell the Chassis or Frame alone for $200. The chassis is in pretty good shape, needs some cage repair and 2 areas straightened where control arms mount. If anyone had an automotive frame machine it would take a few hours.
      That would include....
      Brake calipers, lines, pedal, master cyl, E brake assy,
      Steering shaft, wheel
      Ignition switch, key
      Light bar frame, 2 lights
      misc hardware, spindles
      2 hubs, rotors
      Engine mounts
      Throttle pedal, cables
      Shifter, cables
      Clutch master, pedal
      I am sure I am forgetting something.
      I am parting this out of ebay right now, I just picked up another project and could use the room. No I will not take less than $700 for all of it or $200 for the frame. I do not need to sell it, I will make far more parting it out but would like the extra space in the garage.
      If interested I also have an 07 1000rr engine setup I would sell with the buggy for $650.
      Thanks!
















    • Kyler
      Trail wagon TW450
      By Kyler
      Put new fuel in this thing, new battery I can get it to turn over but want stay running it’ll try to run with starting fluid but shuts right back off what could the problem be?

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...