Quantcast
Jump to content


Recommended Posts

Posted

i got a very simple baffled bottle from the local muffler store. it was about $40 i mounted it sideways across the rear much the same as all the pictures you see on here. it knocks the noise down enough to make the wife happy. you cant hear me coming from very far away but you can definatly hear me as i pass.

  • 2 weeks later...
Posted

I don't know how quiet of a muffler you are looking for, but I used an EMPI clamp on. I think Lenny used same/similar. In my opinion its reasonably quiet. Its similar to a supertrapp at half the cost. The two biggest selling points are that the disc-type mufflers qualify as spark arresters, REQUIRED for off-road use in Arizona (check with your local DFS/BLM/DNR/etc, but its legit in AZ). Secondly, it's low back pressure for turbo those of us turbo charging and blowing our motors.

http://www.empius.com/vwcatalog/2013/133.html

Check out catalog P/N: 3736 (what I used) or for something even quieter, check out P/N: 3738

  • Like 1
Guest Lenny
Posted

I use the same muffler/spark arrestor except mine is the 10" long one #3736. The 17" long one will be a little quieter. I'm happy with mine. I do not run a catalytic converter.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Popular Now

  • Similar Topics

    • By rdc
      I posted this before , but I had the year wrong. The part I need is for a 2014, I don't know what all years will work, but I need the 2 bearing style with the spacer in the middle. It looks like this pic. If anyone has one I'll buy it rite away. my email is [email protected]. Thanks, RC

    • By BWF
      I have a 2011 or so Landmaster LM200.  I cannot get it to start.  I turn the key and nothing happens.  The brake switch seems to be working, the ignition switch works.  The Coil is new the Voltage Regulator is new and the starter relay is new.
       
      I can connect the terminals on the starter relay and it starts right up and runs fine.  I just can't get it to start by turning the key.
       
      I am having a bit of trouble bleeding the brakes, not much fluid comes out at the calipers when I am pumping the brakes, though that an air bubble near the brake switch might make it not sense that the brake pedal is depressed.
       
      I am at a loss, please help!
       
      Brad
    • By rdc
      Hope I posted this in the right place. Looking for the left side shaft carrier where the rear bearings go for an 1100cc sand viper, I understand an 800 cc carrier will also work. I need the old style two bearing with the spacer in the middle, the new style with just the one wide bearing wont work. If anybody has one I'll buy it right away. my email is [email protected]
    • By Jeff freeman
      I have a Coleman 550.  Was having problems to start with where it would start and then shut off after a couple tries. It would take off and be good. It then got to a point where it would not start at all. I replaced the fuel injection twice the second time I replaced it I noticed a mouse or something had chewed one of the wires that connect the electrical to the fuel injector. . So two-part question first does anybody have a part number for that wire harness?  Second, any other ideas after I fix the wire harness permanently on what could keep it from starting I have gas flow up to the fuel injector.


    • By Timbo
      I never see videos of hear of people taking these things to the big trails. Do you ? I just got one and want to.
       
×
×
  • Create New...