Quantcast
Jump to content


Hydraulic clutch setup

rwwiefer

By rwwiefer
in Joyner UTV SxS Forum

 Share

Recommended Posts

rwwiefer Contributor

rwwiefer

Posted
Posted

Hey guys, I picked up a used slave cyclinder with a bracket on ebay, I believe it was off a trooper. I alreay had a 7/8 CNC master cylinder off a class 1600 off road buggy. The bracket does fit the hols in the tranny but won't work on my commando because of the stack exhaust. Does anyone have some pictures of how there slave and master cylinder are mounted. Fabrication is not a problem but with the clutch angle and getting the master low enough for the proper throw it is pretty close to the tie rod. In a violate nose dive not sure if it would hit.

rwwiefer Contributor

rwwiefer

Posted
  • Author
Posted

Does anyone have any picture of the hydraulic clutch set up. Moutning of slave cylinder and master cylinder. Having trouble finding a suitable location to mount the master cylinder and have the right angle for the push rod. Please help.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • rdc
      Looking for the left side shaft carrier where the rear bearings go for a 2014 1100cc sand viper, I understand an 800 cc carrier will also work.
      By rdc
      I posted this before , but I had the year wrong. The part I need is for a 2014, I don't know what all years will work, but I need the 2 bearing style with the spacer in the middle. It looks like this pic. If anyone has one I'll buy it rite away. my email is [email protected]. Thanks, RC

    • RBonds007
      2019 Cub Cadet Challenger 400, trailer to transport the Challenger, and new, never used winch for sale
      By RBonds007
      I bought this SxS brand new.  A couple of years after I bought it, I became disabled.  Thus it has only 47 miles and around 16 hours of use.  I have no need to keep the SxS.  I am in Foley, Alabama.  It is very hard for me to get in out of the Challenger.  I would like to sell the set, 2019 Challenger 400, trailer and uninstalled winch (this was bought brand new as well, someone was supposed to help this newbie install and we never got around to doing this). I want  $6500 for the whole set OBO (Serious offers only).











    • Jeff freeman
      Utv wont start and broken fuel injection wire
      By Jeff freeman
      I have a Coleman 550.  Was having problems to start with where it would start and then shut off after a couple tries. It would take off and be good. It then got to a point where it would not start at all. I replaced the fuel injection twice the second time I replaced it I noticed a mouse or something had chewed one of the wires that connect the electrical to the fuel injector. . So two-part question first does anybody have a part number for that wire harness?  Second, any other ideas after I fix the wire harness permanently on what could keep it from starting I have gas flow up to the fuel injector.


    • Timbo
      Does anyone take axis/hisun 500 to Hatfield trails?
      By Timbo
      I never see videos of hear of people taking these things to the big trails. Do you ? I just got one and want to.
       
    • Outlaw Redneck
      How to make a commando transmission work in sand spider
      By Outlaw Redneck
      Hello all. I have a 2005 Joyner sand spider 650 with the dreaded broken output shaft on the transmission. I got ahold of a 2007 joyner commando 650 for cheap that had a bad motor but a good transmission. I got it because everything i read said that the transmission would work but it seems that it will not. Due to the commando being 4x4 it has a selectable locker and a small ring gear using a "idler" gear to turn the ring gear which make the output spin the wrong direction. Is there any way that I can make this thing work? I really dont want a commando,  I like the buggy but if the trans wont work then I can only put my motor in the commando. Any help would be appreciated. I have the ring gear from the original trans but the shaft is broken and the shaft from the commando wont fit the ring gear it doesn't appear. 

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...