Quantcast
Jump to content


2011 610 xc question

richard12354

By richard12354
in Kawasaki UTV SxS Forum

 Share

Recommended Posts

richard12354 Newbie

richard12354

Posted
Posted

:( :blink: I have a mule that I had to start pulling the choke to keep running at about 75 hrs. I have been working on it and its about to drive me crazy. It will go for ways and start running out of fuel. I have cleaned the carb 4 times, replaced the fuel pump, blowed all the lines including the vacum, replaced the fuel and added sea foal additive. The harder load its under it seems to be worse. I even replaced the coil to cover the bases. I am 99% sure its running out of fuel. I have checked the float and needle to be sure its working freely. I really would appreciate any ideas on fixing it. Thanks Richard

  • 2 weeks later...
KAWMECH Apprentice

KAWMECH

Posted
Posted

I WOULD START BY CHECKING VALVE SETTINGS. SECOND, HOW OLD IS THE FUEL IN TANK? THE ETHYNOL IS PLAYING HELL ON CARBURETORS. I WOULD HOPE WITH 75 HRS. ON THE MULE IT WOULD NOT BE CARB DAMAGE BUT YOU NEVER KNOW. 3RD. IS THIS MULE UNDER WARRANTY?

  • 1 year later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • BWF
      Landmaster LM200 Will Not Start
      By BWF
      I have a 2011 or so Landmaster LM200.  I cannot get it to start.  I turn the key and nothing happens.  The brake switch seems to be working, the ignition switch works.  The Coil is new the Voltage Regulator is new and the starter relay is new.
       
      I can connect the terminals on the starter relay and it starts right up and runs fine.  I just can't get it to start by turning the key.
       
      I am having a bit of trouble bleeding the brakes, not much fluid comes out at the calipers when I am pumping the brakes, though that an air bubble near the brake switch might make it not sense that the brake pedal is depressed.
       
      I am at a loss, please help!
       
      Brad
    • Kierobi
      MSU 500 Fuel Pump Ground
      By Kierobi
      Have a MSU 500 that we got from my wife's uncle a while back. We've had it running and hauling around the property but it stopped a few months ago after what I thought was running out of gas and I'm just getting to looking into it. 
      Had fuel to the injector but nothing coming out the injector so swapped with new injector and installed inline filter in the supply hose from fuel pump. Tried again and still nothing but noticed this time that I can't hear the fuel pump priming. 
      Pulled off the electrical connection and I'm getting 12V to the fuel pump but it won't run. Put it on a test bench and got it to run so put test lamp between +ve and -ve terminals on the connector and nothing. Checked against the passenger seat securing post and get a light. 
      Tried chasing the wire back and think that the ground is through the ECU but not 100% sure. Can someone confirm for me? And if it is through the ECU, is the ECU just grounded against the frame or is it wired through to the battery?
      Thanks in advance and hope this all make sense!
    • Butch
      2023 Hisun Axis 700 fuel problem
      By Butch
      I have a AXIS 700 EFI Fuel pump pressure stays at 40 psi and when return line is blocked the pressure goes to 60 psi. and wll only run with return line closed. 
    • mike.s.
      Kawasaki mule model 2010, 4x4, gas motor, sell or trade
      By mike.s.
      SOLD 
       
       
       
       
    • MilSurpYinzer
      Altering running lights
      By MilSurpYinzer
      Anyone decent with electrical work that knows a good tutorial on how to make my running lights switch off all together but also turn back on when I need too? I'd assume that my lights are hard wired to the battery or the fuse panel.
      Vehicle is a Kawasaki Krx 1000
      I'm looking to ad IR driving lights for night vision and short of just putting black tape over the lights I feel this would be a more efficient option and it would be cooler. 

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...