Quantcast
Jump to content


T2 rear axle

bigdan120

By bigdan120
in Joyner UTV SxS Forum

 Share

Recommended Posts

bigdan120 Rising Star

bigdan120

Posted
Posted

Hey guys was out beating the old Joyner up a hill that I buttomed out on and bam! Right rear axle!!!!!

Does anyone have a used one available? Got to pull it apart it looks to have just destroyed the

Cage that the main axle shaft splines into blew apart and lost some bearings. To clarify it is the rear

Inner passenger side or whole axle. And yes I think I found the culprit. Worn swing arm bushings.

As Always. Thanks!

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Thearm
      TW 450 dies on steep hill
      By Thearm
      I have a 2018 TW450 that runs fine on flat ground but dies out when under load going uphill. Changed the gas filter and spark plug with same results. Letting it set for a few minutes it will run until it hits a incline. Belt is not slipping, but the engine just dies out and doesn't even want to run in neutral. Any ideas as to what I can try is appreciated in advance. Also only run non-ethanol for fuel.
    • rdc
      Looking for the left side shaft carrier where the rear bearings go for a 2014 1100cc sand viper, I understand an 800 cc carrier will also work.
      By rdc
      I posted this before , but I had the year wrong. The part I need is for a 2014, I don't know what all years will work, but I need the 2 bearing style with the spacer in the middle. It looks like this pic. If anyone has one I'll buy it rite away. my email is [email protected]. Thanks, RC

    • rdc
      Looking for a left rear shaft carrier (just the carrier) for a 2007 Joyner 1100 sand viper
      By rdc
      Hope I posted this in the right place. Looking for the left side shaft carrier where the rear bearings go for an 1100cc sand viper, I understand an 800 cc carrier will also work. I need the old style two bearing with the spacer in the middle, the new style with just the one wide bearing wont work. If anybody has one I'll buy it right away. my email is [email protected]
    • paul allen
      2016 wildcat tail front axle rubber boot
      By paul allen
      right front axle cv joint boot keeps getting torn up from the inside out....the stock one was damaged from a stick...i have replaced  the axle 4 times with aftermarket axles that fit fine..after 4-5 miles of riding even on grass.the outer boot get torn up from the inside out...all 4 brand new alxes...bearings are fine nothing bent everything fits just fine....nothing seems to be binding.....any thoughts?????
       
       
      thanks...pa
       
    • Sidewinder
      Polaris RZR 800 Rear Differential Pinion Nut Issue
      By Sidewinder
      All mid 2008 through 2014 Polaris RZR 800 series have a big problem with the rear differential pinion nut backing off, allowing the pinion gear to shoot into the rear differential, destroying the rear differential. This has happened with machines with as little as less than 100 miles on them! Reports indicate that there are no problems, nor warnings, until the rear differential grenades, locking the rear axles solid! This requires the machine to be lifted onto a trailer, to be transported for rear differential replacement, as it destroys the case. After failure, rear differential replacement can be quite expensive: labor alone can run from $800-$1200 and a new OEM Spicer rear diff, if you can find one, can run from $1700-$2500! So, if you own any Polaris RZR 800 series between the years of 2008-2014, I recommend that you do this repair before further use of your machine. personally, I have grounded my machine until it can be done. Please check the online post for your own awareness.

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...