Quantcast
Jump to content


wiring problems

pete42

By pete42
in Joyner UTV SxS Forum

 Share

Recommended Posts

pete42 Rookie

pete42

Posted
Posted

Hi folks just purchased a 08 renegade the guy said he put newwireing harness on it but couldn't get it started any one with a good diagram or how tos no start no wire to fuel pump no power a ecu??? Thanks

pete42 Rookie

pete42

Posted
  • Author
Posted

Thanks plumber found out mine it updated to the 09 wiring harness so far I have most engine relays getting power fuses good but the wire for starter silinoid not sure the only wire there is yellow with a round connection not push on type also my new ecu is sparking if touches frame my fuel pump not coming on on key switch 4 wires big red wire hot small red white stripe hot purple wire not hot white wire not hot?

pete42 Rookie

pete42

Posted
  • Author
Posted

Purchased this new harness jmcmotors i have checked for polarity on fuse relay panel 4 out of 6 fuses don't have polarity (fan fuel ignition guages) in 2009 Manuel it shows 7 fuses in panel not 6 but this harness has 6 1 relay has no polarity (fan)the gages don't cycle no power fuel pump no power starter silinoid? I don't know if this harness will work

pete42 Rookie

pete42

Posted
  • Author
Posted

Update found a black wire that need to be on positive now all fuses are working still no start and gauges are not cycling like before ? Fuel pump still not working does any have a clue what it is I think I'm close.

pete42 Rookie

pete42

Posted
  • Author
Posted

Update found cut wire in new harness what gives ?gages light up cycle over mph tach working no oil no volts no temp ?? And it idles nice no high end power? Any help appreciated ??? Any one there?

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Popular Now

  • Similar Topics

    • BWF
      Landmaster LM200 Will Not Start
      By BWF
      I have a 2011 or so Landmaster LM200.  I cannot get it to start.  I turn the key and nothing happens.  The brake switch seems to be working, the ignition switch works.  The Coil is new the Voltage Regulator is new and the starter relay is new.
       
      I can connect the terminals on the starter relay and it starts right up and runs fine.  I just can't get it to start by turning the key.
       
      I am having a bit of trouble bleeding the brakes, not much fluid comes out at the calipers when I am pumping the brakes, though that an air bubble near the brake switch might make it not sense that the brake pedal is depressed.
       
      I am at a loss, please help!
       
      Brad
    • rdc
      Looking for a left rear shaft carrier (just the carrier) for a 2007 Joyner 1100 sand viper
      By rdc
      Hope I posted this in the right place. Looking for the left side shaft carrier where the rear bearings go for an 1100cc sand viper, I understand an 800 cc carrier will also work. I need the old style two bearing with the spacer in the middle, the new style with just the one wide bearing wont work. If anybody has one I'll buy it right away. my email is [email protected]
    • Kierobi
      MSU 500 Fuel Pump Ground
      By Kierobi
      Have a MSU 500 that we got from my wife's uncle a while back. We've had it running and hauling around the property but it stopped a few months ago after what I thought was running out of gas and I'm just getting to looking into it. 
      Had fuel to the injector but nothing coming out the injector so swapped with new injector and installed inline filter in the supply hose from fuel pump. Tried again and still nothing but noticed this time that I can't hear the fuel pump priming. 
      Pulled off the electrical connection and I'm getting 12V to the fuel pump but it won't run. Put it on a test bench and got it to run so put test lamp between +ve and -ve terminals on the connector and nothing. Checked against the passenger seat securing post and get a light. 
      Tried chasing the wire back and think that the ground is through the ECU but not 100% sure. Can someone confirm for me? And if it is through the ECU, is the ECU just grounded against the frame or is it wired through to the battery?
      Thanks in advance and hope this all make sense!
    • Butch
      2023 Hisun Axis 700 fuel problem
      By Butch
      I have a AXIS 700 EFI Fuel pump pressure stays at 40 psi and when return line is blocked the pressure goes to 60 psi. and wll only run with return line closed. 
    • Jody Deville
      Joyner 800 Renegade rear axles
      By Jody Deville
      I’m looking to best place to buy replacement axles for the rear in my buggy. Both axles are bad. Where is the best place to find them?

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...