Quantcast
Jump to content


Recommended Posts

Posted

I have seen a few variations of the new Gear Reduction Box's Has anyone tried the new UTV Solutions Gear Reduction box's or portal box as some say. From what I am seeing the GRB provides 4” of lift by moving the axle centerline upwards by 4” at the wheel hub, allowing for greater ground clearance under the axle center. By moving the axle centerline, we’re able to maintain factory positions and angle measurements on the upper and lower control arms, Axle shafts, and tie rods.

The GRB also provides a wider stance, adding approximately 3” to each side. The wider stance allows you to go over or around the well-beaten path left by other UTVs and ATVs

DSC08491.JPG

DSC08490.JPG

DSC08492.JPG

Click here for full information on the polaris gear reduction box - portal boxes for rzr - can-am-yamaha-honda utv's!!

  • 2 weeks later...
  • 4 weeks later...
Posted

Yes that price would be for the RZR 570. If we could get our hands on a Joyner it wouldn't be that hard to make a box for them as well. We would just need to know spline count on the axle and caliper mounts for it. I would think it would be that much more for it just time and effort. I never knew there was such a demand for custom Joyners out there...

  • 6 months later...
Guest WillieOi
Posted

LEDOS- Производство светодиодных светильников lp 02 40>>>

Фирма Ledos специализируется на производстве и поставке светодиодных светильников в городе Москва. У нас Вы можете приобрести внутреннее и уличное освещение, источники света, а также комплектующие для светильников и прочее. Услуги, которые предлагает компания: подсветка фасадов зданий и сооружений, освещение офисных помещений и прочие виды услуг. Предоставляем скидки своим клиентам. Подробности на сайте Ledos.Su.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Popular Now

  • Similar Topics

    • By AaronD1982
      Next problem with charging system to tackle, any help would be appreciated.
      New starter solenoid....check
      New Voltage Regulator...check.
      Dynamic test to Stator.....bang...pulling like 2 Volts AC
      Problem: Without pulling the part out and stranding the vehicle at the shop forever.... I am trying to find the correct stator or at least one that might not be exact for the Massimo Buck 400S, but fit and connect and do the job if that makes sense.... if anyone has any ideas, please shoot them my way.
    • By paul allen
      right front axle cv joint boot keeps getting torn up from the inside out....the stock one was damaged from a stick...i have replaced  the axle 4 times with aftermarket axles that fit fine..after 4-5 miles of riding even on grass.the outer boot get torn up from the inside out...all 4 brand new alxes...bearings are fine nothing bent everything fits just fine....nothing seems to be binding.....any thoughts?????
       
       
      thanks...pa
       
    • By MilSurpYinzer
      I heard there's several off road festivals out that way. One or two post apocalyptic, the rest just rev and run. Anyone know a good one that offers camping? Any advice for out of state people like hauling, legality, and where to stay?
      Ideally me and the missus would be down for camping out and setting up shop somewhere nearby. That way we can just wake up, load up, and ride.
    • By AaronD1982
      I recently purchased a 2019 or 2020 (no manual) Massimo 400S Buck Series UTV.  It ran fine for a couple days but the low battery light was flashing while it drove.  It then died in the field one day and I was able to jump the battery and get it rolling enough to get back to the barn.  It started both times I turned the key for a couple days after and when driven died 10 minutes later in the driveway.  Even after jumping it had no juice, but with the key out of the ignition it kept trying to start, a quick look on the Google machine and it suggested starter solenoid or ignition switch was the culprit.  Fair enough, let's just order a replacement solenoid, right?  No way Jose....the pin connector on the UTV is a 2-pin white plastic connector and the part received is a 4 pin.  How do I swap that and make it work?  Can I even?  Where do I find correct parts in the future?
    • By Eman85
      I have been searching and can't find much info on these units. Pretty surprising as every other thing I own I find a lot of info on. Researching for tech info and such it's like no one owns any of these yet I see them everywhere. 
×
×
  • Create New...