Quantcast
Jump to content


Recommended Posts

Posted

I just wanted to show you guys my finished electric power steering cost me about $150 to complete and maybe like 12 hrs counting time expend at junk yard,( to pick up a 03 saturn ion e. Steering column and spare linkages )... saw that a guy was selling this kit for about $500 on craigsl.. I went on line and researched a bit so decided to make my own. Not sure if any one has done it not too complicated just time consuming..you will need the 03 ion electric motor, and need to get on ebay and buy this module that a guy sells for about $70, (((module comes with a adjustment knob to set desired torque))helps if you got a welder and some spare steel angle to mount assembly..i will attach some pics ..... haven't been able to take it out but its very easy to turn now..,

post-1941-0-39000300-1426908968_thumb.jpg

post-1941-0-22685400-1426909322_thumb.jpg

post-1941-0-78836200-1426909350_thumb.jpg

post-1941-0-79617700-1426909391_thumb.jpg

Posted

Definitely a nice upgrade. I did mine with a foreign car steering. The guy that sold you the kit made them first for a Corsa B from the UK.. mine works good. Watch high speed with the power cranked up... you definitely could roll it with this kit. Specially with no sway bar.mine is crazy loose at 40mph. Mine will kick out if I abuse it climbing hills locked in all 4's. But my buggy lives on the Rev limiter..!

  • Like 1
Posted

After alot of hard steering the computer shuts itself off so it don't burn up the motor.it usually just takes a few min for it to re-engage. I'm guessing because I run full power all the time.. definitely needed when all 4 locked.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Popular Now

  • Similar Topics

    • By rdc
      Hope I posted this in the right place. Looking for the left side shaft carrier where the rear bearings go for an 1100cc sand viper, I understand an 800 cc carrier will also work. I need the old style two bearing with the spacer in the middle, the new style with just the one wide bearing wont work. If anybody has one I'll buy it right away. my email is [email protected]
    • By Rmillerdesigns
      Hello. I have a 2016 Massimo MSU 500. I was putting on a lightbar and i screwed up and didn't disconnect the battery so when i was taking of the positive cable to put on the power from the lightbar it sparked and now the utv has no power. I turn the key over and all i hear is a chirp. No lights or anything. Everything that comes from the battery to the jumper box up by the battery shows voltage but anything coming out does not such as to the winch or anything like that
    • By a4x4nutt
      2021 uforce 800  turning radius is awful .
      I just bought it  added perfex lift 
      And 1.5 wheel spacers 
      The turning radius was bad before the lift .
      I looked for steering stops under the tie rod boots and steering knuckle for steering stops . Found nothing .
      Are the stops inside the steering rack ?  Is there a replaced steering rack with longer throw to curb this issue ?
      Any suggestions?
    • By dragon
      I need help I have a 2016 Kubota 1100 RTV my tilt steering wheel locked in the upper position after using the side release. The handle works but does not release the steering wheel to a lower position. If anyone knows and easy fix, please let me know any help is appreciated. Be Safe, Thanks!
×
×
  • Create New...