Quantcast
Jump to content


Replacing rear axle 06 commando

Jeff Gammon

By Jeff Gammon
in Joyner UTV SxS Forum

 Share

Recommended Posts

Jeff Gammon Apprentice

Jeff Gammon

Posted
Posted

The old axle came out without much trouble. I installed the new one. After driving it around some I noticed some rear end grease leaking from the diff. There is a gap between the inner cv and the diff now that I didn't notice before. I can't get the axle to go in any farther or I can't get it to come back out. Any ideas or suggestions?

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Xov
      New AMP Pro Owner
      By Xov
      Just received delivery of a 2024 AMP Pro.  Thought I'd start a thread with my impressions as I use it and learn more.  There doesn't seem to be a whole lot of real-world usage information out there on this model.  Hope this will help others as they research.
      Intended Use Cases
      Fire mitigation / slash removal from a 5 acre forested and well-gamble-oaked property.  The previous owners thought as much about fire mitigation as I do about fashion: not much. Snow removal Stump pulling General hauling (rock, lumber, etc.) Weimaraner energy depletion.  Wasn't an original use case, but a nice added bonus.  Experiences So Far
      Wasn't impressed that two of the bumpers on the underside of the bed where it sits upon the frame were missing.  The metal on metal contact has damaged the powder coating and the frame.  I expect a little better QC.
      I've only put a few hours on it, so not a ton to report on usage.  It isn't quiet; it's silent.  I can't even detect an electric note from the motor. I removed (and subsequently replaced) the motor cover noticed that the motor is German and made by Schambuller.  The motor controller is Italian and made by Dana TM4.  Given the operating specs of both I found on the web, I suspect both are higher quality than the previous Navitas (which is supposed to be decent).  The motor is rated at 25 hp and 71.5 lb-ft of torque.  It feels very powerful.  All the torque is delivered instantly, if desired.
      The bed is huge and has an electric dump as standard.  Great feature but would like it to go up a bit more.  Probably not feasible from an engineering perspective, but I want and I need ;).
      Power steering is nice, but vague.  Probably common to many UTVs, but I am accustomed to more direct results from input.  Plan early and plan often.
      In our first full day of usage, we hauled about 1/2 as much slash as the entire rest of the year when I was doing it by hand cart.  I may get fatter, but I'll also get more done.  After a few days of usage, the battery meter has gone down by 1/10th. 
      Until next time...


    • Tim n Deb
      2015 Massimo stalled and wont start. oil, new plug, getting gas verified. cranks but does not start
      By Tim n Deb
      Riding out today it acted like it ran out of gas,  stalled and died and would not start.   Towed back to house,  New  plug added this past month,  plenty of oil, getting plenty of gas, battery cranks good.   Trys to kick in and starts but doesnt.   Two days prior while sitting at a idle it died.  Added gas and it started did my ranch chores with it.  But just now it stalled out cranks but will not start.   Tried to find if fault codes came up on the clock like manual says but not sure I am doing that right.  Any and all help apprecated.  Thank you
    • Karlibob
      2020 Tracker 800 sx front end noise
      By Karlibob
      I have a 2020 800 sx with about 16 hours on it.  From day one I have heard a clunking noise from the front end going over bumps.  Has anyone else experienced this?  Also this past weekend while out riding I heard a noise that sounded like the dump bed bounced three or four different times, again has anyone experienced anything like that.  Thanks, gary
    • Homeowner A
      Diagnostic Trouble Code Help?
      By Homeowner A
      I was randomly and briefly able to connect to my Coleman UTV 400s ECU the other day twice and haven't been able to since.  When I was able to access it, I found the following codes and wondered if anyone may know where I should start or what I should look at?  
      P0031 - O2 Sensor Heater Control Voltage Low
      P0107 - Manifold Absolute Pressure/Barometer Pressure Voltage Low
      P0113 - Intake Air Temperature Sensor Voltage High
      P0118 - Engine Coolant Temperature Sensor Voltage High
      P0650 - Malfunction Indicator Lamp (MIL) failure
       
    • rdborra
      Bobcat 2200 dump bed relay pops fuse and stalls after warm
      By rdborra
      I had to remove the relay for the dump bed due to it popping the fuse for main key power. I have tried to find a short but nothing seems to out of normal. I also disconnected the dump motor and switch and still pops the fuse. Also, when the machine is warmed up i get about 5 to 10 of work out of before it stalls. Once I can get it to start again I have to use the choke to keep it running. 

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...