Quantcast
Jump to content


Recommended Posts

Posted

my hisun died on me while driving it started losing power then stalled. it wants to start but wont . it didn't over heat. I replaced plug,fuel filter injector, and fuel pump.put code reader on it and says no codes. have any ideas possibly sensor? Any input on what it could be would be appreciated

Posted

go back to the basics. check compression, check spark, remove injector and crank to see if fuel sprays. Sprays!, not drips or squirts like an old man.

I already suspect a plugged up injector. If so, you can try to clean it up, but they're not expensive. I would recommend also adding an inline filter.

Good luck. Keep us posted

Pop Bob

  • Like 1
Posted

Man, I agree with Pop Bob that it is likely the injector.  Some Hisuns were manufactured and sold without an in line fuel filter.  There have been several videos on line of folks suffering from the resulting clogged or malfunctioning injectors.   They simply do not like anything in the fuel they are spraying.    Adding an in line fuel filter is easy, and an absolute must. 

  • 1 month later...
Posted

i dont know i was driving and it started losing power so i shut it off. then 10 min later started it went about 500 feet down road then it just died. the motor made no weird noises or anything like backfiring or clanking. The mechanic said it hit the valves.he said he tried resetting timing chain and while cranking it it jumped again.so waiting for parts to come in and get rebuilt at shop. the machine only has 300 hours on it.sucks i only put 30 miles on it after I bought it used

Posted

Unless you know the former owner, there is no telling what kind of life it had in its 300 hours.   Maybe you have already gone over the machine but check for signs of rough use. Do zerks and joints appear to have been maintained, brake pads, hidden areas packed with mud?  I know its a UTV but there may be signs of it being "abused" as opposed to just being "used".

Sorry you are having such issues.  

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By BWF
      I have a 2011 or so Landmaster LM200.  I cannot get it to start.  I turn the key and nothing happens.  The brake switch seems to be working, the ignition switch works.  The Coil is new the Voltage Regulator is new and the starter relay is new.
       
      I can connect the terminals on the starter relay and it starts right up and runs fine.  I just can't get it to start by turning the key.
       
      I am having a bit of trouble bleeding the brakes, not much fluid comes out at the calipers when I am pumping the brakes, though that an air bubble near the brake switch might make it not sense that the brake pedal is depressed.
       
      I am at a loss, please help!
       
      Brad
    • By Burk
      I have a 2021 Axis(Hisun) 700 from Lowes. Will not start. Checked starter, solenoid, spark plug and fuel pump. Everything seems to be fine. The motor turns over and will try to start but just will not. Battery is also good. Frustrated!
    • By HISUN Sector 750 EPS Failu
      "Mrs. Smith" doesn't like how loud our Sector 750 is.  On a HISUN forum someone said the same thing about his 750.  I haven't given it much thought because I've been more focused on stuff that has broken.
      So, I used my decibel meter to check ours out.  4000 RPM, Low gear, under 20 MPH . . . . 97 decibels.  That's above most ordinances, even state boat noise limits.
      AI Overview Ninety-seven (97) decibels is considered very loud and dangerous to hearing with prolonged exposure, roughly equivalent to a newspaper press, a loud nightclub, or a snowmobile. At this level, damage can occur after just 30 minutes, necessitating hearing protection
    • By Kierobi
      Have a MSU 500 that we got from my wife's uncle a while back. We've had it running and hauling around the property but it stopped a few months ago after what I thought was running out of gas and I'm just getting to looking into it. 
      Had fuel to the injector but nothing coming out the injector so swapped with new injector and installed inline filter in the supply hose from fuel pump. Tried again and still nothing but noticed this time that I can't hear the fuel pump priming. 
      Pulled off the electrical connection and I'm getting 12V to the fuel pump but it won't run. Put it on a test bench and got it to run so put test lamp between +ve and -ve terminals on the connector and nothing. Checked against the passenger seat securing post and get a light. 
      Tried chasing the wire back and think that the ground is through the ECU but not 100% sure. Can someone confirm for me? And if it is through the ECU, is the ECU just grounded against the frame or is it wired through to the battery?
      Thanks in advance and hope this all make sense!
    • By Hunterman22
      Can anyone please tell me or send a link as to how & where to hook up a code reader to my 2021 Hisun 500 Axis.  I have a 6 pin to a 18 pin  adaptor and the blue cord VAG KKL adaptor .Just not sure where or what to hook up to. Can I use your typical vehicle code reader or do I need to download something on a laptop or PC???
       
×
×
  • Create New...