The other day i removed my battery to check the acid level in it. It was still full. as i was reinstalling the positive cable the nut on the terminal stripped out. This battery uses a threaded insert that you slide into the terminal the bolts screws into, I was able to tigthen it up, but it's the kind of deal where if you kept turning it would get loose then tight, loose then tight. So after an unsuccessful trip to the parts store, tractor supply and hardware store, no one had what i needed, so then i did the smart thing and contacted Yuasa. Gave them all the battery specs and i now have new hardware kit on the way to me for FREE. For now i have a small pair of vice grips holding it, in case the bolt were to come loose while driving until i get a new hardware kit in. I did find the kit later on Summit racing, for $6. but hey, this is Free.
By Steve Vanvelzen
I Recently purchased a Massimo T-Boss 550F last fall with their 60" snow thrower because I couldn't find a decent UTV here in Southern Ontario; nothing in stock anywhere. I am having really bad buyer's remorse after spending time on it and reading all the bad online reviews. The company boasts the fact that it is built in Texas, USA, so I was hoping to do the right thing by buying, "Made In North America" but it is still Chinese Junk, assembled in the USA. and I am starting to realize that I am going to have a lot of difficulty getting parts for this thing; I can't even get an oil filter, finally bought a "Hisun" filter and hope it fits. i busted the shear pins in the snow thrower and can't find replacements for that either. The thing is so hard to change gears most of the time; I am terrified I am going to wreck something. The place I purchased it from is absolutely useless. Can I adjust something myself? Anyone out there have this problem and have some advice (besides selling it and buying a good brand)?
The middle two tires on 6x6 are spinning. the drive shaft from middle to rear is spinning and the shaft from middle to front is spinning. I have the entire thing jacked up. When I first start it both middle tires will spin and the front two will spin for about 10 seconds. the rear tires do nothing. I can spin the rears wheels both forward or backwards at same time or one forward and one backward and vise versa. Is this normal. Do I have a rear differential broke or is something not engaging the shaft to the gears in the back. Would somebody please tell me how all the drive system works together so I can find something to fix of replace.
I have an American Landmaster LM500 with an old style snow plow hook-up. Unfortunately, the mounting bracket broke & I lost the key part where the plow receiver connects to the cross bar with two pins.
I checked with customer service & they said...
On Monday, January 10, 2022, 03:25:29 PM EST, Feedback <[email protected]> wrote: Sounds like it may be the old style push tube universal mount system, it looks like those have been discontinued but we may still have some back there. I believe they are sold as a kit though and they are not cheap, part # 15329. I’ve included a photo below since the web store does not have a photo for that part.
I checked with our parts department and neither the kit or the components are available as that was the older style hook up system. The only option at this point would to have something manufactured. All of our current plows are either dual actuated or winch hookup so we would only have components for those models as of currently.
In the picture, below, it would be item #5 (the one with the two mounting brackets that hold the pins that the plow mount latches onto) - not the top one in the picture, but the one below t hat.
I have all the other parts - but the missing part is critical to mounting the plow.
Does anyone happen to have an old one they could part with - or have an alternative solution?
The rig wasn't optimal, as you had to use the winch to raise & lower the blade & manually adjust the angle. It kept falling off when I was plowing snow - as the pins that hold it in only have a groove for a pin clip & they would often get knocked off & then the plow would hang down & you'd loose the pin - then it would get all messed up.
Thanks in advance for any advice. I am thinking of going to a welding shop to see if they can create something - but it will still have the same limitations as before - the pins are highly specific and not cheap
15331 Pin, Shear Univ Mount Blade PART #: 15331