2005 Joyner 800cc Sand Viper FOR SALE
-
Similar Topics
-
By rdc
I posted this before , but I had the year wrong. The part I need is for a 2014, I don't know what all years will work, but I need the 2 bearing style with the spacer in the middle. It looks like this pic. If anyone has one I'll buy it rite away. my email is [email protected]. Thanks, RC
-
By rdc
Hope I posted this in the right place. Looking for the left side shaft carrier where the rear bearings go for an 1100cc sand viper, I understand an 800 cc carrier will also work. I need the old style two bearing with the spacer in the middle, the new style with just the one wide bearing wont work. If anybody has one I'll buy it right away. my email is [email protected]
-
By MilSurpYinzer
I heard there's several off road festivals out that way. One or two post apocalyptic, the rest just rev and run. Anyone know a good one that offers camping? Any advice for out of state people like hauling, legality, and where to stay?
Ideally me and the missus would be down for camping out and setting up shop somewhere nearby. That way we can just wake up, load up, and ride.
-
By Sidewinder
All mid 2008 through 2014 Polaris RZR 800 series have a big problem with the rear differential pinion nut backing off, allowing the pinion gear to shoot into the rear differential, destroying the rear differential. This has happened with machines with as little as less than 100 miles on them! Reports indicate that there are no problems, nor warnings, until the rear differential grenades, locking the rear axles solid! This requires the machine to be lifted onto a trailer, to be transported for rear differential replacement, as it destroys the case. After failure, rear differential replacement can be quite expensive: labor alone can run from $800-$1200 and a new OEM Spicer rear diff, if you can find one, can run from $1700-$2500! So, if you own any Polaris RZR 800 series between the years of 2008-2014, I recommend that you do this repair before further use of your machine. personally, I have grounded my machine until it can be done. Please check the online post for your own awareness.
-
By 180gtr
Parting out a rolled Sand viper 1100. I will list some of the parts I have, otherwise ask me if there is something specific you are looking for. I am selling everything I have for $800. I am located near Glenwood Springs CO.
SOLD ITEMS, I do not have these items.
Wheels
Tires
Engine
Transmission
Axles
Shocks
Control Arms
Things I have....These all came off of the running engine. I have video of it running if anyone needs to verify that.
Throttle Body $90
Starter $150
Alternator $150
Fuel rail, injectors, fpr $100
fuel pump $70
Map Sensor $50
Full set of Guages $150
Exhaust w cat, O2 SOLD
Ignition Coil - SOLD
Wiring harness and ecu SOLD
Radiator, shroud, elec fan, overflow tank $200
Fuel tank w sender $150 Has dent at base of fuel neck, no leaks
I have a box full of misc bolts, nuts, etc.
I will sell the Chassis or Frame alone for $200. The chassis is in pretty good shape, needs some cage repair and 2 areas straightened where control arms mount. If anyone had an automotive frame machine it would take a few hours.
That would include....
Brake calipers, lines, pedal, master cyl, E brake assy,
Steering shaft, wheel
Ignition switch, key
Light bar frame, 2 lights
misc hardware, spindles
2 hubs, rotors
Engine mounts
Throttle pedal, cables
Shifter, cables
Clutch master, pedal
I am sure I am forgetting something.
I am parting this out of ebay right now, I just picked up another project and could use the room. No I will not take less than $700 for all of it or $200 for the frame. I do not need to sell it, I will make far more parting it out but would like the extra space in the garage.
If interested I also have an 07 1000rr engine setup I would sell with the buggy for $650.
Thanks!
-
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.