Quantcast
Jump to content


Need advice on trooper supercharger install

Volkz VLOGS

By Volkz VLOGS
in Joyner UTV SxS Forum

 Share

Recommended Posts

Volkz VLOGS Contributor

Volkz VLOGS

Posted
Posted

Hi, I'm getting ready to supercharge my trooper and I'm looking for advice on the setup. So far I have... a AMR500 supercharger, small intercooler, Dolbeck EJK fuel controller and wideband. Looking for any advice on what else I'm going to need and what to expect..Thank you

 

 

 

Volkz VLOGS Contributor

Volkz VLOGS

Posted
  • Author
Posted

Thanks! This is exactly the type of thing I'm looking for advice on! Do you know the specs of the one I'll need?  Would it be a 5v 1w? Also from the 1100 service wiring diagram it showed 1 is pressure signal 3 is temperature signal and 4 is ground.. And  the first diagram shows the diode between signal and ground. So I'm guessing the diode  goes between 1&4 and not 1&3 like you Drew on the paper...?

  • Like 1
dwaynebradley377 Enthusiast

dwaynebradley377

Posted
Posted
Thanks! This is exactly the type of thing I'm looking for advice on! Do you know the specs of the one I'll need?  Would it be a 5v 1w? Also from the 1100 service wiring diagram it showed 1 is pressure signal 3 is temperature signal and 4 is ground.. And  the first diagram shows the diode between signal and ground. So I'm guessing the diode  goes between 1&4 and not 1&3 like you Drew on the paper...?
Yes been so long ,5v 1w works ,think your right 1-4 , I also got a field controller from dobeck but I had them max out to 12millisec or the longest pulse available " been couple years hard to remember "
Running a gt15 turbo seems to work fine

Sent from my SM-G930W8 using Tapatalk

  • Like 1
Volkz VLOGS Contributor

Volkz VLOGS

Posted
  • Author
Posted

Ok cool! Seems I'll be basically replicating something similar to your setup just supercharger instead of Turbo, until I can go megasquirt later like Lenny(hopefullywhen i have more money)!... So if you could run down everything you had to make it work, I'd appreciate it..  Did your dobeck have a  vac/boost line.. Because I've seen ones with it and I have the one without it... Also did you have to go water/meth injection or 100 octane anything like that.. Thanks..

dwaynebradley377 Enthusiast

dwaynebradley377

Posted
Posted
Ok cool! Seems I'll be basically replicating something similar to your setup just supercharger instead of Turbo, until I can go megasquirt later like Lenny(hopefullywhen i have more money)!... So if you could run down everything you had to make it work, I'd appreciate it..  Did your dobeck have a  vac/boost line.. Because I've seen ones with it and I have the one without it... Also did you have to go water/meth injection or 100 octane anything like that.. Thanks..
Forgot went to ejk after 1st programmer broke
Used these setting for basic setupd1906ade94a28b10a5e1a476db2723b0.jpg

Sent from my SM-G930W8 using Tapatalk

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Popular Now

  • Similar Topics

    • rdc
      Looking for the left side shaft carrier where the rear bearings go for a 2014 1100cc sand viper, I understand an 800 cc carrier will also work.
      By rdc
      I posted this before , but I had the year wrong. The part I need is for a 2014, I don't know what all years will work, but I need the 2 bearing style with the spacer in the middle. It looks like this pic. If anyone has one I'll buy it rite away. my email is [email protected]. Thanks, RC

    • rdc
      Looking for a left rear shaft carrier (just the carrier) for a 2007 Joyner 1100 sand viper
      By rdc
      Hope I posted this in the right place. Looking for the left side shaft carrier where the rear bearings go for an 1100cc sand viper, I understand an 800 cc carrier will also work. I need the old style two bearing with the spacer in the middle, the new style with just the one wide bearing wont work. If anybody has one I'll buy it right away. my email is [email protected]
    • Kierobi
      MSU 500 Fuel Pump Ground
      By Kierobi
      Have a MSU 500 that we got from my wife's uncle a while back. We've had it running and hauling around the property but it stopped a few months ago after what I thought was running out of gas and I'm just getting to looking into it. 
      Had fuel to the injector but nothing coming out the injector so swapped with new injector and installed inline filter in the supply hose from fuel pump. Tried again and still nothing but noticed this time that I can't hear the fuel pump priming. 
      Pulled off the electrical connection and I'm getting 12V to the fuel pump but it won't run. Put it on a test bench and got it to run so put test lamp between +ve and -ve terminals on the connector and nothing. Checked against the passenger seat securing post and get a light. 
      Tried chasing the wire back and think that the ground is through the ECU but not 100% sure. Can someone confirm for me? And if it is through the ECU, is the ECU just grounded against the frame or is it wired through to the battery?
      Thanks in advance and hope this all make sense!
    • Butch
      2023 Hisun Axis 700 fuel problem
      By Butch
      I have a AXIS 700 EFI Fuel pump pressure stays at 40 psi and when return line is blocked the pressure goes to 60 psi. and wll only run with return line closed. 
    • Jeff freeman
      Utv wont start and broken fuel injection wire
      By Jeff freeman
      I have a Coleman 550.  Was having problems to start with where it would start and then shut off after a couple tries. It would take off and be good. It then got to a point where it would not start at all. I replaced the fuel injection twice the second time I replaced it I noticed a mouse or something had chewed one of the wires that connect the electrical to the fuel injector. . So two-part question first does anybody have a part number for that wire harness?  Second, any other ideas after I fix the wire harness permanently on what could keep it from starting I have gas flow up to the fuel injector.


UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...