Quantcast
Jump to content


UT400 cutting out mid throttle

Homeowner A

By Homeowner A
in Coleman UTV SxS Forum

 Share

Recommended Posts

Homeowner A Contributor

Homeowner A

Posted
Posted

Have an issue all the sudden where the UTV will cut out randomly mid range throttle and under load.  Light consistent throttle on fairly flat ground no problems.  If you quickly change throttle position sometimes it will bog down and cut out, splutter, etc.  Floor it or let off and it may do just fine.  Going up a hill and adding more throttle as the incline demands, will cut out splutter and smell unburnt fuel.  So far doesn't ever completely quit.  If you let off it will idle just fine.  A lot of times if you floor it, it will pick up and even get a boost of power.  Changed to a slightly hotter plug to see if that would make a difference, but it didn't .  Any ideas what might be going on and what to try next?  

  • 3 weeks later...
Homeowner A Contributor

Homeowner A

Posted
  • Author
Posted

Replaced injector and it has been running well until yesterday. Now it’s cutting out again mid throttle when it gets up to full temp. Possibly misfiring too did smell some unburnt fuel at one point when it would cut out.  Light throttle or flooring it and it does fine. I replaced the injector again but no improvement. Any ideas? What should I look at next?

  • 3 months later...
FrankyHatton Newbie

FrankyHatton

Posted
Posted
On 1/25/2025 at 5:51 PM, Homeowner A said:

Replaced injector and it has been running well until yesterday. Now it’s cutting out again mid throttle when it gets up to full temp. Possibly misfiring too did smell some unburnt fuel at one point when it would cut out.  Light throttle or flooring it and it does fine. I replaced the injector again but no improvement. Any ideas? What should I look at next?

 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Joe Rizo
      2014 Hisun 700 UTV starting problem
      By Joe Rizo
      Hello All,
      We have exhausted all possible troubleshooting steps, now we are in need of some help. 
      Vehicle cranks but will not turn over. Things we have either replaced or tested and are now known good:
      1. Fuel pump (new)
      2. Fuel sensor (new)
      3. Fuel injector (new)
      4. Battery (new)
      5. Spark plug (new), spark tested
      6. fuses (12v to all)
      7. we have 12v at the injector module and 11 ohms resistance
      8. we have fuel in the fuel line to the injector
      9. we have fuel at the spark plug
      10. we have injector pulse, verified with noid tester
      11. brake safety switch tested (couldn't find a separate switch assuming it is using the brake light switch)
      12. seat belt buckled and seat in place (again, not sure if this model has these features)
      13. replaced air filter
      14. replaced several air hoses
      15. flushed radiator and replaced with diluted antifreeze
      16. Drained and cleaned the fuel tank prior to replacing the fuel pump.
      Any ideas, we are open to....Help!!
       
    • Rschrem
      2010 700 Hisun starter issue
      By Rschrem
      Hi, my 2010 Hisun will crannk but comes to a stop and only clicks.  It has new battery and solinoid. Battery connections all seem good. Any ideas what the problem is? 
    • hetovi
      Best UTV Windshield for Extreme Conditions
      By hetovi
      Hey everyone,
      I’m in the market for a UTV windshield that can withstand extreme conditions, including high winds, dust, and off-road impacts.
      I’ve seen a lot of options out there, but I’m unsure which one will provide the best protection and durability.
      Does anyone have experience with windshields that excel in these environments? Are there specific brands or materials you recommend?
      I’m particularly interested in options that offer both durability and clarity.
      Any tips or personal experiences would be greatly appreciated!
    • Joe Breaux
      Oil change
      By Joe Breaux
      Decided to do an oil change on the Massimo ...drained oil, screen was very clean even tho oil wasn't.  Then went to remove old filter.. holy crap ..I tried every tool I have, could not budge it..Went to store and got one of the end cap type..fit nice and tight, put a 1/2 in drive ratchet on it..nope..not moving.  Put a 18 on breaker bar o. It. The inside of the removal tool broke off!!  Had to weld it back together. Put a pipe on the bar for more leverage.  Finally broke it loose..
      I have never seen a filter in my 55 yrs of working on engines so tight..And i was the one who put it on 2 yrs ago.  JUST HAND TIGHT!
       
    • Pick a name
      Shifting issue
      By Pick a name
      The Axis 500 will not shift into low or reverse.  I have high when it should be in low and all the other places it is reverse.  The gears in the shift cover are fine and I shifted it when the cover was off and yet no change (so it can't be the shifting mechanism gears).  I t has been difficult to get it into low for awhile.  But now it is either high or reverse, no neutral either.

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...