Quantcast
Jump to content


Cub Cadet Volunteer 747EFI

RussVT

By RussVT
in Cub Cadet UTV SxS Forum

 Share

Recommended Posts

RussVT Newbie

RussVT

Posted
Posted

Centralized front drive fluid change. The manual says it's below the gear box and takes 6oz of 10w40. Does anyone know how to change this. E.g. where the drain and fill plug are? Perhaps a picture or drawing depicting?

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Tim n Deb
      2015 Massimo stalled and wont start. oil, new plug, getting gas verified. cranks but does not start
      By Tim n Deb
      Riding out today it acted like it ran out of gas,  stalled and died and would not start.   Towed back to house,  New  plug added this past month,  plenty of oil, getting plenty of gas, battery cranks good.   Trys to kick in and starts but doesnt.   Two days prior while sitting at a idle it died.  Added gas and it started did my ranch chores with it.  But just now it stalled out cranks but will not start.   Tried to find if fault codes came up on the clock like manual says but not sure I am doing that right.  Any and all help apprecated.  Thank you
    • Joe Breaux
      Oil change
      By Joe Breaux
      Decided to do an oil change on the Massimo ...drained oil, screen was very clean even tho oil wasn't.  Then went to remove old filter.. holy crap ..I tried every tool I have, could not budge it..Went to store and got one of the end cap type..fit nice and tight, put a 1/2 in drive ratchet on it..nope..not moving.  Put a 18 on breaker bar o. It. The inside of the removal tool broke off!!  Had to weld it back together. Put a pipe on the bar for more leverage.  Finally broke it loose..
      I have never seen a filter in my 55 yrs of working on engines so tight..And i was the one who put it on 2 yrs ago.  JUST HAND TIGHT!
       
    • Kevin Ullman
      2015 Polaris RZR900 Service Manual
      By Kevin Ullman
      View File 2015 Polaris RZR900 Service Manual
      2015 Polaris RZR900 Service Manual
      Submitter Kevin Ullman Submitted 04/23/2025 Category Polaris  
    • Kevin Ullman
      2013-2016 Polaris RZR 570 Service Manual
      By Kevin Ullman
      View File 2013-2016 Polaris RZR 570 Service Manual
      2013-2016 Polaris RZR 570 Service Manual
      Submitter Kevin Ullman Submitted 04/23/2025 Category Polaris  
    • Karlibob
      2020 Tracker 800 sx front end noise
      By Karlibob
      I have a 2020 800 sx with about 16 hours on it.  From day one I have heard a clunking noise from the front end going over bumps.  Has anyone else experienced this?  Also this past weekend while out riding I heard a noise that sounded like the dump bed bounced three or four different times, again has anyone experienced anything like that.  Thanks, gary

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...