Quantcast
Jump to content


Recommended Posts

Posted

The E1 has a small 12v battery to run the instruments, lights etc. You can't connect a light bar to the Discover Dry Cell batteries. Individually, they are 6 volts, but there's eight of them in series to make 48 volts that runs the motor. In the battery compartment under the seat, you'll see the dry cell batteries, but also a smaller ATV-type 12v battery directly underneath where you sit to drive. There's a fuse and relay box down there too. I'd recommend not fiddling around in there unless you're absolutely sure what you're doing, as the 48v system could cause you a nasty injury if you short it by mistake.

On the UK version, there's a 12v accessory point in the dash along with all the control buttons. There's also a 12v supply to the registration plate light on the underside of the tilting load bed. Either of those should be safe to tap into for a light bar, and are only live when the ignition is on.

  • Like 1
Posted

Never take a 12v tap off the main traction pack. However tempting that may be. If you tap off from a single battery (or two on the Hisuns 6v batteries) that 12v battery (6v batteries) will end up at a lower state of charge than the rest of the pack. This will then impact on the way the vehicle drives , as that lower voltage battery (ies) will reduce the overall performance. Unless you then do significant over charging (All batteries will then get hot) they will never get re balanced again.  And excessive overcharging will cause damage to all the traction pack batteries. Anything attached to the 12v battery or accessory should have its own fuse. As a guide dont put anything on that pulls more than 10a without talking to the dealer as how best to do that.  Especially if the vehicle is still under warranty.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By hetovi
      Hey everyone,
      I’m in the market for a UTV windshield that can withstand extreme conditions, including high winds, dust, and off-road impacts.
      I’ve seen a lot of options out there, but I’m unsure which one will provide the best protection and durability.
      Does anyone have experience with windshields that excel in these environments? Are there specific brands or materials you recommend?
      I’m particularly interested in options that offer both durability and clarity.
      Any tips or personal experiences would be greatly appreciated!
    • By Rschrem
      Hi, my 2010 Hisun will crannk but comes to a stop and only clicks.  It has new battery and solinoid. Battery connections all seem good. Any ideas what the problem is? 
    • By Prepper
      I have been doing a little research on which engine oil is best for UTV engines.  There seems to be some disagreement over using a good quality regular engine oil, and the necessity of using "M2" (or wet clutch suitable) oil.  My understanding is the "wet clutch" suitable oil has less friction reduction properties (hence a more responsive clutch with less slippage).  While less friction reduction properties would seem to be better for the wet clutch... it would not be best for the internal engine parts like camshaft bearings and other moving parts where friction is detrimental and would lead to premature failure.  Some folks swear you need M2 oil, while others say they have been using regular motor oil for years and their clutch is just fine.  Could they both be right ???
      Any thoughts ?
       
    • By monkthumper
      Fuel pump is good (i hotwired it) swapped relay with known good one no help. I'm leanin towards ECU but cannot find wiring diagram online. Dont know how fuel pump relay gets its signal, all fuses good, any help? 
    • By BigWave
      I turned off the key and then tried to start it a minute later and it would not start. I changed out the fuel filter and the injector. still nothing. if i have the injector pulled out and close to the hole the injector will spray fuel into the hole and it will run but the minute you put the injector in it will die. any idea's please
       
       
      Bigwave
       
×
×
  • Create New...