Quantcast
Jump to content


Recommended Posts

Posted

I have been working on variations of the Clutching for the 6 Arm design and have had Outstanding results . The Test vehicle is a 21 Turbo RR completely stock. All changes are in the Primary Clutch . The 6 Arm clutch made more power than the P Drive (stock) after the 6 Arm was properly calibrated. Here is the final Dyno pull . This is the stock clutching vs. the Prototype Kit . Very Impressive ......Just wanted to show that you can get plenty of performance out of the 6 Arm clutch and not buy a P Drive . In Fact , i tweaked a P Drive and The Graph was almost identical when both clutches were ran ....Both of these clutches were ran on the same machine ....

 

dynoIMG_3036.jpg

Posted
9 hours ago, klm said:

wish I knew what you  are talking about.

Is it that you do not understand Clutching KLM ? Just wanted to Clairify .. That way I can make sure to answer you correctly ..

Thank you

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By CSM_Retired
      Has anyone installed the power dump on a Kioti K9? If so, does it eliminate the safety lock? Does it work well?
      Thanks for your input
    • By CaptainMorgan
      I have a Bobcat 2200 Diesel (built by Club Car) with a 2-weight Team Primary Clutch I want to rebuild, possibly replace. The clutch has an annoying rattling sound at idle and appears the rollers and weights are worn and loose. When I opened it up, everything looks clean and in great shape. It's just that all the moving rollers and weights seem to have way too much play in them, possibly causing the noise. I've searched for clearance and torque specifications with no luck at all. The UTV has less than 500 hours on it.  Any ideas?
    • By SkyPilot56
      working on a coleman 550 out fitter , had a shit load of codes, coil, injector , and the map sensor for fuel injector replaced all 3 and figured it would start , but no joy have spark (new plug also and inline fuel filter) cleared the codes and still have the engine light , turns over fine but damn thing still will not start, friends daughters were driving it and turned it off to park , and went back to start it and same thing turns over but will not start , with this machine anyone have any ideas as to what the hell , I should be looking for , no plug's unplug checked wires none seem to be pulled apart or broken !
    • By CapnWalleye
      Just picked up a Hisun 500 that had shift issues (corroded fan gear) which I fixed. It also didn't seem to be running smoothly then all of a sudden it got worse. It seems to miss on both idle and when pushing the gas pedal to the floor and doesn't seem to be running at full power. I've been working with a local person who is walking me through some steps, but I'd like some input from this group as well. What I've done:
      - drained the fuel tank and replaced it with 93 octane fuel and added heet to help with any water problems.
      - replaced the fuel injector.
      - disconnected the battery (several times) to allow the module to reset.
      - set the valve clearance, both intake and exhaust, within specs ... intake was tight but exhaust seemed fine.
      - replaced the battery.
      - replaced the O2 sensor.
      Nothing has helped. Not sure what the next steps are, but would appreciate any expertise that can be offered here.
       
    • By A P
      Hi
      I have a 2022 hisun sector eps 550. 30amp fuse is blown for eps. Checked the motor and it’s fine. Opened up the controller and found a bad diode. Dealer wanted 500$ for the controller. Just posting this in case it helps someone. I couldn’t read numbers from the old one so just took a guess and replaced it with a 100v 3amp diode. 
×
×
  • Create New...