Quantcast
Jump to content


Recommended Posts

Posted

I bought a used 1140CPX at an auction.  It was listed a INOP and when it arrived it was.  It runs like a top now and I’m trying to correct the next thing on the list: Lights.

Somewhere along the line, the headlight switch wiring connector was snipped off.  I only have a wire bundle leading to the hole where the headlight switch should be.  I bought a new switch and plan to just solder the wires in permanent.

The question for the forum: Can someone take a photo of what color wire goes to which pin?  I think that will be much quicker than finding the ground and then figuring out which is which.  If I know what to solder to where I’ll be able to drive at night again.  

One last question, what is the best way to add an LED light bar to the front and back and wire it in?

Thanks for the help,

Ryan

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Similar Topics

    • By Sammy
      Runs fine just putting around the yard. Get it out on the road and about a half miles it runs out of gas. Let it idle for a few minutes and it will run for another half mile and do it again. Replaced both fuel pumps and filter. Does anyone know if I can get rid of the factory fuel pump?
    • By AaronD1982
      Onto the next problem, everything has been replaced in the charging system except the Flywheel Rotor, I have it torn apart all the way down to said rotor, but it is suggested that a specific puller is required, and a compatible rotor seems virtually impossible to find.  I can find many like it, but this one is mine scenario for those that get the reference.  For all I know I have the last Massimo Buck 400S on the planet and will never find another part again, but who knows.  Any ideas, help or otherwise that anyone might have would be greatly appreciated.
    • By Mitch13
      2022 Coleman 400 with 13 hours on the engine and the mice got to it. Every wire coming out of the steering column in one cluster has been eaten through. I tried reconnecting matching wire colors to each other and I get the left turn signal and hazards to work, nothing else. If I play around a bit I can get the horn to honk or headlights to come on but only when I connect them to the brown wire. Obviously I don't know what I am doing here. Does anyone have a picture of how these wires are connected when they are under the hood on the drivers side coming from the steering column?
      Gray - seems to carry power
      Brown - left turn signal
      Green with purple stripe - hazards?
      Pink with red stripe - horn?
      Green - head lights?
      Yellow - head lights?
      Yellow with red stripe?
      Blue?
      Dark green?
      There is also a bundle hanging under the hood not connected to anything green with yellow strip, brown and blue?
      Other than that issue, I am about ready to sell this for parts if you interested let me know.
      Thanks
    • By RBonds007
      I bought this SxS brand new.  A couple of years after I bought it, I became disabled.  Thus it has only 47 miles and around 16 hours of use.  I have no need to keep the SxS.  I am in Foley, Alabama.  It is very hard for me to get in out of the Challenger.  I would like to sell the set, 2019 Challenger 400, trailer and uninstalled winch (this was bought brand new as well, someone was supposed to help this newbie install and we never got around to doing this). I want  $6500 for the whole set OBO (Serious offers only).











    • By MilSurpYinzer
      Anyone decent with electrical work that knows a good tutorial on how to make my running lights switch off all together but also turn back on when I need too? I'd assume that my lights are hard wired to the battery or the fuse panel.
      Vehicle is a Kawasaki Krx 1000
      I'm looking to ad IR driving lights for night vision and short of just putting black tape over the lights I feel this would be a more efficient option and it would be cooler. 
×
×
  • Create New...