Quantcast
Jump to content

American Sportsworks 653cc


Recommended Posts

Hi Jim,

I think what you believe to be a vacuum lne is just a drain line from the carb bowl. If you look closely from the backside of carb {flywheel side) you will see a small screw that is really a valve. What model do you have (UTV not engine) and where are you located?

bbirder

Link to comment
Share on other sites

Not sure about Vin #. Didn't get a title with mine. You probably have an older model 700. Does it have single wheel drive , 2 wheel and 4 wheel also. That engine is no longer being made or sold and parts are hard to come by. If you need anything post on here or send me a message. I'll try to help. I'm in South Louisiana.

Link to comment
Share on other sites

Jim,

Try this link to a service manual. It will cost you 5.95 but well worth it. I tried sending my copy but couldn't get it to load correctly. You should be able to get instructions and clearances. Is it running bad or you are just checking? Does your engine have the two barrel carb?

 

https://subaru-robin.servicemanualvault.com/Subaru-Robin-EH65-Engine-Service-Manual.html

  • Thanks 1
Link to comment
Share on other sites

Jim

I'm going to attempt to post the valve adj portion of the manual only. hope it works. Watch closely to ID which cyl is #1 and which is #2. Also be very careful wiring up the coils. The wire coming out from them is the kill wire and the key switch connect it to grd to stop engine. *****IF 12V HITS THAT WIRE IT WILL FRY THE COILS . i know because my grandson was helping me and made that mistake. Took me forever to find two coils and they were used and expensive.

valve.adj.eh65.pdf

Link to comment
Share on other sites

Jim, I"ve only seen the double barrel. Saw the single in thge book but not sure if ASW ever used it. The Nikki double barrel is used by severa;l enginde mfg such as Briggs and Kohler. Simple to work on but the carbs are configured differently for other mfgs.Question.......Is your engine running? If it is, I would leave well enough alone until you need to get into it. Sometimes we want to take things apart and clean them and create a bigger problem than we had. Only go after troubles!

Link to comment
Share on other sites

Ooooh-kay. Video sheds a different light on things. Did you strip body panels or did you get it w/o the wrap? TGhose may not be avai;lab ler and if so yhou vcan probably buy a new u nit for what they will cost you. Sounds like trash in the carb `or possibly the governor sertting is off. When removing carb go easy on the four all thread rods that hold it in place. They strip easy in the manifold .I have a book on that carb, I'll find it and send to you. I've never had to change a jet but the orings may go bad. Did you get the repair manual ordered?

Link to comment
Share on other sites

  • 1 month later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By didgeridoo
      Hello, All!  I've decided to replace the traction batteries in my 2018 Sector E1 with a 48V Lithium set. They may be expensive, but I figure the Discovery Dry Cell are, too. I am not looking for the max driving range, as I have never received near the brochured range to begin with, but a good mix of charge/ get work done/ charge is what I am expecting.
      I have settled on the 48V EAGL kit from bigbattery dot com. Each battery pack provides 30Ah. The kit ships with a charger, as well. The packs would be physically connected in parallel (using a busbar) to one another, maintaining the 48V voltage, but together would be able to provide the amp draw the buggy pulls when going up hill or towing a rake (rated 320 max continuous Amps). This is in comparison to the serial connection the eight 6V lead batteries. Each of the EAGL batteries looks to have its own BMS; am I correct in thinking I will have to use their included charger rather than (simply) changing the onboard charger to lithium mode? The chemistry of the pack is LiFe PO4, for what it's worth.  I haven't torn anything apart yet (to diagram), so  I am not sure how the dash will interpret the AMP draw, but the kit I am looking at includes a dash mounted charge indicator.
      If anyone has completed a similar conversion, do you have any tips? Specifically, how did you remove the original batteries, and how did you secure the new ones? I am guessing that almost any change from the stock batteries would involve at least some modifications. Any tips would be appreciated, especially things I may have failed to consider. Thanks!
    • By Clyde says
      I have a 2014 landmaster S/S 4x4 model 653 4x4 with a 22 hp robins engine. I've been having problems with the govenor reving after it running a short distance. I cleaned the carb and discovered the fuel membrane has a slight pin hole (P/N 210-253). Can not seem to locate a replacement. Any suggestions? It appears this carburetor is no longer supported.
    • By Steve B
      My "R" light on the dash will not go out when I take the UTV out of reverse and put it into any other gear. Is this just the light switch issue or will this effect engine performance in the other gears?
    • By REDfletching
      Spent today at a Honda dealership looking at their 520 side by side, then on the way home past our Lowes noticed they had several new UTVs on site, so we U-turned and ducked in there. We were impressed that all that came for $9,999 metal whole length skid plate, nice sized bed, roof, windshield, side mirrors, winch, upgrade looking tires… all of which would have added thousands of dollars to an already expensive Honda 520. Now Honda does have a great reputation from my trusted UTV experienced buddy, so it has that going for it.
    • By Hugh
      My 2018 Hisun sector crew engine cut off after about 15 minutes run. There is no indicator of what is wrong, no error code just die and won't restart until it cool down. I notice that the fan is not running but the temp indicator is on low temp, no overheat indicator. I checked the radiator fluid, it is cool to touch.
      Cooling fans are working, I can hear it running once awhile if I can get the engine warm up enough.  Thank you for all the help.
       
      Hugh
×
×
  • Create New...