Quantcast
Jump to content

2015 Bennche cowboy 700 efi starting issues

Mikeh91

By Mikeh91
in Bennche UTV SxS Forum

 Share

Recommended Posts

Mikeh91 Newbie

Mikeh91

Posted
Posted

Machine was running rough(everything is in time and valve clearance is good) it would bog down on a hill then shut off then take forever for it to fire back up. But now it won't turn over. Replaced the solenoid but not getting power to the small plug on the solenoid at all. I've checked everything I could and even pulled the main harness apart to look for broken wires. It never did this until timing chain broke and it was replaced.
 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • DLJ
      Hisun 800 shuts down
      By DLJ
      Have a Hisun 800 it runs for about 35 minutes then stalls. Crank's over but has no spark. Let it sit for 15 to 20 minutes and it starts and runs again for about 35 minutes. Changed the CDI / ECU controller and still does it.
    • Ermd ttk
      UTV Odes Ravager 1000cc - Strange noise from the back
      By Ermd ttk
      Hello friends,
      I got my ODES Ravager UTV yesterday and after a couple of hours of driving when I go downhill I heard a strange loud noise a couple of times, like a gear skipping or maybe something from the differential.
      It doesn't always happen and when it does it is heard for a few seconds and then it goes away and everything works normally, I'm worried if there could be some major malfunction or what could be the problem if someone can help me?
      Thanks a lot.
       
    • joeam
      2018 Landmaster Tw450E will not run down the road?
      By joeam
      I have a 2018 TW450E that runs in my yard and slow good just will not go down the road seems to be running out of fuel where should i start? I have replaced both fuel and air filter drained gas and tried a small auxiliary tank same issue i have ordered a new vacuum fuel pump to try next anyone in Texas that works on these?
    • packersfan
      Hisun 500 very hard to turn
      By packersfan
      I have a hisun 500 got from a auction and when turning a corner left or right it's a two hand job then when you left go snaps back.any help on what to look at would be appreciated.
      Also blows blue smoke until she gets warm then it's ok 
    • Jon C
      UT400 valve lash
      By Jon C
      Hello to anyone who reads this. I am Jon and I own J&M Outdoor Power, a very small, small engine repair shop. I was approached by Coleman about 6 months ago to become one of their Warranty Centers.
      I recently received 3 different UT400's and a UT500 all with similar issues. These units range from 2 months to 2 years old. Customers state that the unit(s) was/were running fine, then heard a pop and a loss of power, two would no longer start. The two that would run would not achieve normal operating speed (around 20mph I would say) without redlining the RPMs. I quickly found that the Valve lash on each unit had become too large on some(both intake and exhaust) and too tight on one(just intake). 
      After setting the gaps to .005(I found multiple different people suggesting bigger and smaller gaps, but no definitive Coleman Spec number yet) every unit starts, runs, and achieves top speed without issue.
      I don't know how many others have come across these issues, and I wanted to get something out on the web for others in the same predicament. 
      Please let me know if you have had similar issues.
      Edit: I realize that this will not be a fix all solution for this issue, as the oil level and condition should be verified before moving to the valves. Many times improper oil conditions will cause valve lash to change. These units all have good oil and proper oil changes.

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...