Quantcast
Jump to content


2014 Massimo MSU500 Primary clutch issues

Bob Marshall

By Bob Marshall
in Massimo UTV SxS Forum

 Share

Recommended Posts

Bob Marshall Newbie

Bob Marshall

Posted
Posted

I know this topic has come up many times before but I see nothing that duplicates my issue. I replaced the wet clutch and after reinstalling the primary things changed. i had to realign the weights in the clutch because they came out of the slot. Now I have a knocking in the clutch that I cant find the source .  I know the one way bearing is correct - spins clockwise and turns the crank if turned CCW. I have included the YT link. The primary is engage enough at idle that I cant put in gear while its running. Idling  @ 1300 rpm. Tried new belt and old belt with no improvement. I am not sure the primary should be turning at idle which points to the wet clutch? I started the engin with the primary off and no knocking occurred 

 

 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Rschrem
      2010 700 Hisun starter issue
      By Rschrem
      Hi, my 2010 Hisun will crannk but comes to a stop and only clicks.  It has new battery and solinoid. Battery connections all seem good. Any ideas what the problem is? 
    • CaptainMorgan
      Bobcat 2200 Diesel Primary Clutch Rebuild
      By CaptainMorgan
      I have a Bobcat 2200 Diesel (built by Club Car) with a 2-weight Team Primary Clutch I want to rebuild, possibly replace. The clutch has an annoying rattling sound at idle and appears the rollers and weights are worn and loose. When I opened it up, everything looks clean and in great shape. It's just that all the moving rollers and weights seem to have way too much play in them, possibly causing the noise. I've searched for clearance and torque specifications with no luck at all. The UTV has less than 500 hours on it.  Any ideas?
    • Pick a name
      Shifting issue
      By Pick a name
      The Axis 500 will not shift into low or reverse.  I have high when it should be in low and all the other places it is reverse.  The gears in the shift cover are fine and I shifted it when the cover was off and yet no change (so it can't be the shifting mechanism gears).  I t has been difficult to get it into low for awhile.  But now it is either high or reverse, no neutral either.
    • KWinTX
      Information on 2024 Hison 550x Stryker with a No start Issue
      By KWinTX
      I just bought a new 2024 Hison 550 Stryker 2 months ago. this is the second time I have had this issue.  It only has about 20 hours on it. The last time it happened we took it back to the dealer. it was a fuse.  Since we live three-hour time driving there and back. I would like to find another solution if possible.  I have tried all the fuses that seem to have anything to do with starting.  Currently checking the battery. The battery is new. it came with the unit. It is probably 6 months old.  the UTV has all power to everything electrical. lights turn signals and radio all work.  When trying the key to start . it is 100% dead. as in it doesn't even click.  There is a low whirring like the fuel pump is turning on though. The Unit was running and driving just fine.  we shut it down for the night. The next morning my wife found it in this condition.  Thanks for any Ideas or solutions???   Otherwise, it goes back to the dealer tomorrow. Just hope I didn't buy a lemon. Great little UTV when it does run.😅  anyone else ever have this Issue..? 
    • rdborra
      Bobcat 2200 dump bed relay pops fuse and stalls after warm
      By rdborra
      I had to remove the relay for the dump bed due to it popping the fuse for main key power. I have tried to find a short but nothing seems to out of normal. I also disconnected the dump motor and switch and still pops the fuse. Also, when the machine is warmed up i get about 5 to 10 of work out of before it stalls. Once I can get it to start again I have to use the choke to keep it running. 

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...