Quantcast
Jump to content


MSU 500. Runs but will only move with full power.

William Carberry

By William Carberry
in Massimo UTV SxS Forum

 Share
Go to solution Solved by Kenh,

Recommended Posts

  • Solution
Kenh Newbie

Kenh

Posted
  • Solution
Posted
24 minutes ago, klm said:

Yes it does, hard to change.

How old is it, how many hours/miles?

I have a 2017 Massimo MSU500 side by side. It's not really that hard I have changed mine a couple of times to include the clutches primary and secondary also the wet clutch.

klm Enthusiast

klm

Posted
Posted

I have a 2014 and have changed it once.  Not that hard but not fun.

I was just thinking that if a guy didn't even know weather it had a drive belt or not, it might be a little difficult.

  • 2 weeks later...
William Carberry Newbie

William Carberry

Posted
  • Author
Posted

OK. I think its a 2016 or so not sure of the hours not a lot but it has a decent amout. And to those of you being critical, Your right I don't know a lot about these but I can usually figure it out. I just wanted to know so I have a jumping off point. Thanks 

William Carberry Newbie

William Carberry

Posted
  • Author
Posted
On 12/1/2023 at 7:53 PM, klm said:

I have a 2014 and have changed it once.  Not that hard but not fun.

I was just thinking that if a guy didn't even know weather it had a drive belt or not, it might be a little difficult.

Maybe not but I am willing to learn.

  • 1 month later...
BearR Newbie

BearR

Posted
Posted

Did you find resolution to your issue?  I am working on a 2018 Sector 750 and that is the same issue it was having.  I just got the wet clutch cover off and the clutch is bad.  Clutch material is missing and the clutch hub that is supposed to be machined smooth is grooved. Take your plastics off so you can get to the belt cover and then inspect the belt and primary & secondary pulleys/sheaves.  If no issues with those, remove those and the back of the belt cover then remove the wet clutch cover to inspect.  YouTube has videos on removing all those parts.  Also, check out the service manual here on utvboard.com.  

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • BWF
      Landmaster LM200 Will Not Start
      By BWF
      I have a 2011 or so Landmaster LM200.  I cannot get it to start.  I turn the key and nothing happens.  The brake switch seems to be working, the ignition switch works.  The Coil is new the Voltage Regulator is new and the starter relay is new.
       
      I can connect the terminals on the starter relay and it starts right up and runs fine.  I just can't get it to start by turning the key.
       
      I am having a bit of trouble bleeding the brakes, not much fluid comes out at the calipers when I am pumping the brakes, though that an air bubble near the brake switch might make it not sense that the brake pedal is depressed.
       
      I am at a loss, please help!
       
      Brad
    • Kierobi
      MSU 500 Fuel Pump Ground
      By Kierobi
      Have a MSU 500 that we got from my wife's uncle a while back. We've had it running and hauling around the property but it stopped a few months ago after what I thought was running out of gas and I'm just getting to looking into it. 
      Had fuel to the injector but nothing coming out the injector so swapped with new injector and installed inline filter in the supply hose from fuel pump. Tried again and still nothing but noticed this time that I can't hear the fuel pump priming. 
      Pulled off the electrical connection and I'm getting 12V to the fuel pump but it won't run. Put it on a test bench and got it to run so put test lamp between +ve and -ve terminals on the connector and nothing. Checked against the passenger seat securing post and get a light. 
      Tried chasing the wire back and think that the ground is through the ECU but not 100% sure. Can someone confirm for me? And if it is through the ECU, is the ECU just grounded against the frame or is it wired through to the battery?
      Thanks in advance and hope this all make sense!
    • Hunterman22
      2021 Hisun 500 Axis. Reading Codes??
      By Hunterman22
      Can anyone please tell me or send a link as to how & where to hook up a code reader to my 2021 Hisun 500 Axis.  I have a 6 pin to a 18 pin  adaptor and the blue cord VAG KKL adaptor .Just not sure where or what to hook up to. Can I use your typical vehicle code reader or do I need to download something on a laptop or PC???
       
    • Jeff freeman
      Utv wont start and broken fuel injection wire
      By Jeff freeman
      I have a Coleman 550.  Was having problems to start with where it would start and then shut off after a couple tries. It would take off and be good. It then got to a point where it would not start at all. I replaced the fuel injection twice the second time I replaced it I noticed a mouse or something had chewed one of the wires that connect the electrical to the fuel injector. . So two-part question first does anybody have a part number for that wire harness?  Second, any other ideas after I fix the wire harness permanently on what could keep it from starting I have gas flow up to the fuel injector.


    • Eman85
      Fuel injector replacement Massimo 500
      By Eman85
      Pulled fuel injector to see if I could clean it or if it's stuck open. Had a slide on clip that was really tough to get off. Don't see how the clip is supposed to lock into the plastic part that the injector slides into. Any videos or pics of injector replacement? 

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...