Quantcast
Jump to content

MSU 500 - draining fuel tank


Recommended Posts

Bought a Massimo 500 last night. Stopped and filled it up on the way home and I put the wrong gas in it. Is there a drain plug on the bottom of the tank that I can get to or will I have to siphon it out?

Link to comment
Share on other sites

On 3/20/2024 at 3:01 PM, Round said:

Bought a Massimo 500 last night. Stopped and filled it up on the way home and I put the wrong gas in it. Is there a drain plug on the bottom of the tank that I can get to or will I have to siphon it out?

From the 2014 and 2016 I've worked on it's a Siphon job. Mine are one piece Molded plastic tanks. 

 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By Buddee
      Put a new carb on the 500 to replace the leaking OE one.  Machine idles fine and mid and top end runs great.  It tends to have a hesitation right from the start - bottom end.   Thinking it may be the air/fuel screw??  I didn't do anything with the carb out of the box and is it direct replacement for my machine.  Of interest is the manual choke doesn't seem to work very good now.... wonder is it getting too much air?
       
      Any help appreciated!
       
       
    • By great8redsfan
      Okay folks. I have a low power issue. Been like this for a few years. Place I work at bought 3 and all have lost most of the pulling power.  They gave them away after local shop worked on one for 3 months and it had great power for about 1 month and then crap. They replaced throttle body, fuel injector, spark plug and IAC motor. Seat belt switches have wires cut and left open so no seat belt warning light anymore. It revs to 6k rpm in neutral but when put in gear and take off in low it just doesn’t seem to want to go anymore. Running 93 octane fuel with Stabil.  Any ideas greatly appreciated. I dont have a scan tool but no codes on dash. If held to floor it pops a little and runs almost 5K rpm but if I let off pedal about an inch it smoothed out and revs up to 6k rpm. 
    • By htrotte
      #1   While troubleshooting an issue with temp warning light I discovered another temp switch mounted in the pipe going to the head  The two switches are literally 6 inches apart.  Does anyone know what this third switch is used for?  If i can figure out how I will post pictures.
      Author #2   Finally got the pictures took.  See the photo and tell me if you know what the switch on the right is.
      It looks to be factory and I know the girl who bought it new and she didn't install it.
      I can't find anything on it in any manual i have looked at.  Any help would be appreciated.

    • By joel b
      i purchased a brand new massimo tboss 410 and from day 1 it wont operate in reverse.  When i pop in reverse and give it gas it will die out.  when i pop in reverse sometimes in will die right away (before giving any gas) and 1 time out of 100 when i pop in reverse it will operate perfectly fine.   and yes, it operates perfectly dine in normal drive H and L.  any thoughts??   when i called the dealer i got it from they had no idea.  
    • By Mark T
      MY 400 is gutless. I would like to know if I can upgrade to a larger engine ?
×
×
  • Create New...