Quantcast
Jump to content


Renegade owners in Kentucky.


Recommended Posts

I need a R2 and R4 to use as a model to get a full enclosure fitted out. If you live near Carlisle, Kentucky and would like a below cost enclosure for your efforts, please contact me. It should only take two weeks, but as we found out last time, it can take a lot longer. I also need a Trooper to go back for a couple of days to re-design just the soft front panel. If anybody lives close that owns a Commando two or four seater, I’d also love to hear from you. Your UTV will be used for promo photos, so will need to be clean.

Cheers Mike.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By great8redsfan
      Okay folks. I have a low power issue. Been like this for a few years. Place I work at bought 3 and all have lost most of the pulling power.  They gave them away after local shop worked on one for 3 months and it had great power for about 1 month and then crap. They replaced throttle body, fuel injector, spark plug and IAC motor. Seat belt switches have wires cut and left open so no seat belt warning light anymore. It revs to 6k rpm in neutral but when put in gear and take off in low it just doesn’t seem to want to go anymore. Running 93 octane fuel with Stabil.  Any ideas greatly appreciated. I dont have a scan tool but no codes on dash. If held to floor it pops a little and runs almost 5K rpm but if I let off pedal about an inch it smoothed out and revs up to 6k rpm. 
    • By BOYD
      I have a 2004 KUBOTA RTV 900 DIESEL and I need to replace both front cv axels.I have been online looking at them and there seems to be a lot of different manufactures to choose from. My question is who makes a good aftermarket set of cv axels for this KUBOTA. I have read horror stories of people buying the  cheap Chinese brand only to find out they don't fit or they don't last very long and fail again. I hate to have to spend over $200 a shaft to get OEM from KUBOTA when I'm sure there is a company out there who probably makes it for them or makes comparable to OEM. Thanks for your help.
    • By Greg Kilgore
      I would really like to know what you guys think about this. I'll try not to ramble and make it as clear as I can.
       
      I took this new job with companyX as a fiber splicer a year ago. I have a 45' bucket truck and 10or12 x 8 ft enclosed splice trailer I have to take home. Within the last 6 months all the management in the splice dept left. Now the power/construction management and higher ups are filling in. Just recently we were told travel to our 1st job is not payable even though we are in a company vehicle. 
      We are union so I asked the union business manager about this. His reply was be grateful you were paid travel as long as you were and that you don't have to drive your POV to the job.
       
      Last week I had 50hr total. The job area is 4-4.5 hrs away. My time was reduced to 44.5 hrs since we were told this travel thing on Tuesday of that week. I wasn't hired for this area. I was hired for area a lot closer to home. 
       
      Pay is good. Work is not hard. Insurance is through the union and so far pretty good.
      But I hate the thought of having to work extra just to make a 40hr paycheck. Anyone who has to drive as part of their job knows windshield time is not easy.
       
      Anyway what do you guys think. Should I look for a different job or just suck it up because of the decent pay and health insurance.
    • By Richard shepard
      I have a 2021 colman 400utv engine will start and idle, as soon as you hit throttle to move engine dies and will only start when you throttle it, let off throttle it dies, I replaced the injector and plug still the same, anyone have any other ideas
    • By LindaCall60
      Purchased a 2011 bighorn banchee. Needs motor work. Not sure what. Husband is mechanic but not computer savvy. So, is there a manual that will tell him how to tear this down?  We have down loaded a service manual, but he says it doesn't tell him what he is looking for. 
×
×
  • Create New...