Quantcast
Jump to content


Recommended Posts

Posted

new to the forum, had a 08 trooper t2 for 3 years and was online looking to see what was availabe for upgrades, seemed to find the most info on this site. have added 30" ZILLA's and a set of QA1 coil overs. i have ordered a silver bullet fuel controller and air / fuel ration gauge. i hope it performs as advertised. have had to replace the 4 wheel shifter ( was full of water ) and the fuel sender crapped out on the last ride. currently have about 1350 miles on it and my only real beef with it is all the rattles, they seem to pop up everywhere, fix 1 and you find a new one the very next day. thinking about power steering, does anyone have any recomendations on this ?

thanks

Posted

Welcome.

I had a '08. Yes they have more rattles than the rest because they used more wielded metal in the panels. What I had to do was caulk ALL the seams, floors, storage compartments under the seats (they were the worst), everywhere you can get to with the caulk (just get a good quality outdoor CLEAR caulk from Home Depot or local hardware store). Took care of most of the rattles except in the steering. That requires Lenny's steering upgrade kit or replace the steering rack. Hang in there, you will get most of them.

rocmoc n AZ/Mexico

Posted

thanks rocmoc, winter is coming up here in alberta and i dont ride it in the snow, i think this winters projects will be to try your caulking, get the steering rack looked after and hopefully find a good electric power steering kit to install. i am also having the same oil pressure problem many other talk about so i think the cooler add on is in order.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Popular Now

  • Similar Topics

    • By rdc
      I posted this before , but I had the year wrong. The part I need is for a 2014, I don't know what all years will work, but I need the 2 bearing style with the spacer in the middle. It looks like this pic. If anyone has one I'll buy it rite away. my email is [email protected]. Thanks, RC

    • By rdc
      Hope I posted this in the right place. Looking for the left side shaft carrier where the rear bearings go for an 1100cc sand viper, I understand an 800 cc carrier will also work. I need the old style two bearing with the spacer in the middle, the new style with just the one wide bearing wont work. If anybody has one I'll buy it right away. my email is [email protected]
    • By Kierobi
      Have a MSU 500 that we got from my wife's uncle a while back. We've had it running and hauling around the property but it stopped a few months ago after what I thought was running out of gas and I'm just getting to looking into it. 
      Had fuel to the injector but nothing coming out the injector so swapped with new injector and installed inline filter in the supply hose from fuel pump. Tried again and still nothing but noticed this time that I can't hear the fuel pump priming. 
      Pulled off the electrical connection and I'm getting 12V to the fuel pump but it won't run. Put it on a test bench and got it to run so put test lamp between +ve and -ve terminals on the connector and nothing. Checked against the passenger seat securing post and get a light. 
      Tried chasing the wire back and think that the ground is through the ECU but not 100% sure. Can someone confirm for me? And if it is through the ECU, is the ECU just grounded against the frame or is it wired through to the battery?
      Thanks in advance and hope this all make sense!
    • By RBonds007
      Looking for an online parts store.  Just need basic maintenance parts tune ups and such.  Any suggestions?
    • By Butch
      I have a AXIS 700 EFI Fuel pump pressure stays at 40 psi and when return line is blocked the pressure goes to 60 psi. and wll only run with return line closed. 
×
×
  • Create New...