Quantcast
Jump to content


Mule jumps out of forward gear

Will

By Will
in Kawasaki UTV SxS Forum

 Share

Recommended Posts

Will Newbie

Will

Posted
Posted

I just bought a 1994 Mule KAF450 b-1 and when I got it home found that it popped out of forward gear. I'm waiting for a manual to help troubleshoot it but think that the cause may be the shifting dogs on the shuttle shifter and the forward gear are rounded off. Anyone had any experience with this type problem? I'm not sure if those parts are still available and if not may try to weld the parts and reshape them to rebuild the dogs.

Thanks...

Will

  • 1 month later...
4 dog knight Rookie

4 dog knight

Posted
Posted

Will,

I went thru a similar predicament, but mine was a broken internal case where the shifter shaft went thru the top of the case. I tried welding it but that didn't work because the hole was too elongated. If I had access to a milling machine it could've been bored straight and had a bushing inserted. My gears were in fine shape...it was just not able to shift into place due to the sloppy shaft. One other critical issue is that you get the idle down below 900 RPM or it won't want to drop into gear. The driven clutch is spinning over pretty fast to slide those gears into place if the idle is too high. These things will idle down to nothing if the carb is clean, etc. You may adjust the shifter cable to put more pressure on the cable. Unfortunately, it "pushes" the cable into forward, while pulling it into reverse. You can adjust it to a point where it won't clear the nuetral notch in the dashboard if you go too far. It also won't start, as it needs to sense the nuetral shifter position. I did have to replace my cable, as it was too wippy and wouldn't push the shifter shaft into the proper position.

Good Luck!

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • nrggaragebuilds
      2004 Joyner Dirt Devil Missing “Prick gear”
      By nrggaragebuilds
      2004 250DL DIRT DEVIL. Hey y’all, I already know this is a long shot. But I am looking for a the “prick gear” assembly that makes reverse work for my external reverse gearbox. OEM PN D250.08.103 and its assembly. I bought the kart as a basket case, but I saw that the reverse box was present so I was optimistic.  Upon starting working on the buggy I realized there was a block off plate in plate of there the normal gear would be. If my understanding is correct that means the transmission no longer has reverse gear. I figured it’s just a standard bevel gear and I could probably find a gear to make work, but I don’t want to spend the time making all the other housing parts to shim the gear perfectly. Has anyone spare parts, or figured out an aftermarket solution from McMaster? I already know it’ll be a challenge to get this box to be happy again, but figured I would ask  
    • AlphaSerenity
      Hisun Axis 500 Problems - Hesitation, struggles to go up incline, and low speed regardless of gear range
      By AlphaSerenity
      Hello,
      Before I invest $10k+ into a brand new UTV for the farm, I want to get my feet wet with a fixer upper and learn the mechanical side of things. I acquired a 2022 Hisun Axis 500 (Lowes-specific model) from an auction for $500. It has only 200 hours and 120 miles on the engine. It looks like the previous owner used it for ranch work and didn't drive it on trails, deep water/mud, or anything too crazy.
      While it runs and moves, it has some problems. It struggles to accelerate up any incline in high and low range and sometimes stalls when I let off of the throttle or change gears. When I apply throttle in neutral, it sounds like it is struggling for fuel/air and pops. When I decelerate, there is a grinding sound coming from the clutch, which I've read to be related to the one way bearing and is semi-common. The last thing I've observed is sometimes the speedometer display sometimes will show a much higher value for a few seconds after barely touching the throttle. Based on the documentation, if a problem is detected from the sensors, the instrument panel display should have an error code rendered on the screen in place of the time, but this isn't happening. Here is a video showing some of these issues (engine is exposed with console removed):
      https://www.youtube.com/watch?v=FFAkO5TaGps
       
      Here is another video of the clutches in action:
       
      I've done some research, but information on this specific unit and sister units is limited. There does seem to be transmission and clutch issues reported. I still need to check into the head gaskets. I don't have the equipment to test compression right now, but I do plan on ordering what is needed soon. I do have an order in place for some cables to read the diagnostics from the computer. There is a shop two hours away from me that works on Hisun products, but I am hoping the problem can be identified and is something within my ability to handle. Below is what I've already investigated.  I am leaning towards the primary clutch needing replacement right now.
      After getting it home and unloaded, I did the following maintenance/checks to it prior to operating it further:
      Changed the engine/clutch oil (and filter) and gear oils using manufacture recommended viscosity Changed the air filter and checked for cracks in the air intake flow. Verified good suction. Cleaned the throttle body Changed the spark plug and verified the gap was within spec (0.6-0.7mm) Changed the coil and coil wire Changed the fuel lines, fuel injector, and verified the fuel pump was outputting the correct initial prime pressure for ignition and continuous pressure after ignition. Also completely emptied the fuel tank and made sure octane 91+ fuel is being used per manufacturer specs. Ran seafoam through system too. Cleaned the spark arrester and verified no cracks or gaps in the exhaust flow Changed out the O2 sensor Checked all wired connections to ensure they were secured and no breaks were visible Checked the belt for tightness and for any signs of wear and tear Verified 4WD and the differential lock function as expected - still hesitates and struggles uphill Verified the fan gears in the shifter are not corroded and working as expected ECU was reset after replacing sensors and fuel-related parts  
       
      Thanks!
    • AaronD1982
      Hoping someone out there somewhere can help.....2019 Massimo Buck 400S
      By AaronD1982
      Onto the next problem, everything has been replaced in the charging system except the Flywheel Rotor, I have it torn apart all the way down to said rotor, but it is suggested that a specific puller is required, and a compatible rotor seems virtually impossible to find.  I can find many like it, but this one is mine scenario for those that get the reference.  For all I know I have the last Massimo Buck 400S on the planet and will never find another part again, but who knows.  Any ideas, help or otherwise that anyone might have would be greatly appreciated.
    • Debbie Hogan
      1999 kawasaki mule 550 c3 exhaust pipe oem part 496021126
      By Debbie Hogan
      I realize this part is discontinued but im trying to find this exhaust pipe fir my dads 550.  His brother who has since passed bought this mule for my dad who is now 90 and he is trying to fix everything on it.  I'm willing to take a used one.  A new one would be great if someone still had in stock.  I'll take anything as long as it is in workable condition.   If anyone has any ideas for me im open to hearing them.  Thank you so much.
       
      Debbie fm  Texas
    • rdc
      Looking for a left rear shaft carrier (just the carrier) for a 2007 Joyner 1100 sand viper
      By rdc
      Hope I posted this in the right place. Looking for the left side shaft carrier where the rear bearings go for an 1100cc sand viper, I understand an 800 cc carrier will also work. I need the old style two bearing with the spacer in the middle, the new style with just the one wide bearing wont work. If anybody has one I'll buy it right away. my email is [email protected]

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...