Quantcast
Jump to content


Renegade and trooper front diff difference

nocturnalsixer

By nocturnalsixer
in Joyner UTV SxS Forum

 Share

Recommended Posts

nocturnalsixer Rising Star

nocturnalsixer

Posted
Posted

Well i went out to install my shimmed renegade front diff and pull out the old t2 diff that was still in the t2. Before anyone makes this mistake.....pull out the t2 front diff and compare the axle stubs that cv half shaft go over and make sure they are the same. I'm going to have to tear it down and rebuild/shim it all over my mistake for thinking renegade and trooper share exact same diff. Everything is same except for pinion on rear diff but on front diff its the pinon and side gears.

http://db.tt/Ws1MPpf2

http://db.tt/AL6ucrTN

http://db.tt/igusXr0K

http://db.tt/tbAuM5aN

Sent from my DROID RAZR using Tapatalk 2

nocturnalsixer Rising Star

nocturnalsixer

Posted
  • Author
Posted

Kinarfi...my rear had the right diameter splines so renegade rear matched up to trooper no problem but front threw me off. I don't know why that is like that i looked up in t2 manual it even said that front is supposed to be smaller and on my t2 it's all same front and rear i'm sure that's same for everyone else here?

Sent from my DROID RAZR using Tapatalk 2

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • GBarney
      d1105T install in rtv 1000?
      By GBarney
      Recently bought a 2010 RTV 1100 with bad engine. a d1105T out of a toro 5400 just came available locally. Looking for info on if anybody has installed the turbo version of this engine, what challenges/ problems were encountered, how it turned out.
       
      Looks like nobody has any insight. I will complete installation and report back as to how it went, how it works, and what's involved.
    • Karlibob
      2020 Tracker 800 sx front end noise
      By Karlibob
      I have a 2020 800 sx with about 16 hours on it.  From day one I have heard a clunking noise from the front end going over bumps.  Has anyone else experienced this?  Also this past weekend while out riding I heard a noise that sounded like the dump bed bounced three or four different times, again has anyone experienced anything like that.  Thanks, gary
    • D MAYNARD
      Axis 500 4x4 turns over but no spark
      By D MAYNARD
      I have an Axis 500 4x4 UTV that I was given.  It looks like an almost new machine with 39 hrs on it however it was apparently under water from the hurricane . I have no spark at the plug. I have replaced the plug, the plug wire, & the stator so far. Can anyone advise me of what i need to check and or replace to get this thing running? Any advise would be greatly appreciated. 
                                    Thank You,
                                  D Maynard 
       
    • staind
      Joyner R2 2008 800cc ECM code reader Lite or OBD port install
      By staind
      Looking for information on installing a OBD port or a lite to read codes in ECM. 
      I can not find a OBD port or a lite to read codes on this R2 with 800cc. 
      I have code readers and adapters for most ATV's. From what I've found so far. They don't have a connection for to read codes. I may be wrong. That's why I'm asking. 
      This R2 has had new IAC, TPS, MAP, fuel pressure regulator and fuel pump replaced. This was done by neighbor to try to stop surging. It still surges on start up and then settles down. But once you hit the accelerator it revs up to 2000+ rpm and stays till you block off IAC port in throttle body with finger. Once you do that it once again settles down and idles perfectly.
      I want to know what the ECM is reading to help dio it.
      This joyner is the first one I've run across. Well second one in a week. (my neighbors 2 of them) The other was a trooper with the 1100cc chery motor that had been setting for years. After cleaning up the fuse box connections. It runs like a top. Had to replace all gages with aftermarket gages. Water, oil, gas, amp. Only problem one was the water temp using original sending unit. Had to install 150 ohm resistor on the input wire to get it to read correctly + - 5 degrees. Close enough. Gas sending unit was/is for a boat tank 6" tall. All SS so it should last forever. 
      thanks Dan D. aka staind
    • mcraigchr
      550 - Diff fluid change and final drive?
      By mcraigchr
      Howdy y'all,
      I have the service manual, but it leaves me with questions.
      1)  It is time to change the diff fluid.  The service manual says 80w-90 for the rear and Dextron 3 ATF for the front!  Is that correct?  That seems odd to me.
      2) The service manual also speaks of the need to change the transmission fluid but gives no detail about it.  What needs to happen here?
      3). The service manual also discusses changing the final drive fluid with 80-90 Hypoid.  Is the final drive actually the tranny?
      Any details about the changing of the fluid or what fluid to use ... or even other things that need to be changed that the manual does not mention would be appreciated.
      Thanks,
      Craig C.  

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...