Quantcast
Jump to content


Recommended Posts

Posted

think you would need to jump a line from your main one to the parking brake with a double banjo bolt like this on in the link , this company in the link sell all the parts u need i just dont no the sizes of the banjo bolt and fitting u would need. the sell quick connect fittings so no special tool necessary. i did it this way when i added another rotor to the front motorcycle worked out great.

http://www.spieglerusa.com/double-banjo-bolt-1651.htm

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By GaryC
      Unfortunately my rear Diff housing cracked on my 2013 and I need to replace it or find a good used complete differential.  I think the same one was used from 2013-2016?  Any help or referrals appreciated.  Thanks, Gary  (949)370-2575 (in UT)
    • By lowgear52
      Has anyone purchased a rear differential from Alibaba, they want $432.00 for diff and $35.00 for shipping. This would be a great deal if I can trust them any thoughts?
    • By Cletus
      I have a 2016 550, ive tryed the hisun website and seems i cant get parts there. I would like to add power steering, have seen a few "kits" on ebay
      for the 750 not sure if its the same parts needed for the 550, there is a factory bracket already welded to the frame above the standard steering rack, is this to be used
      to mount the eps motor? There is also a grey plug hanging just above the brake master cylinder, not sure if thats anything that needs to be used in the install.
      Handy with wrenches so if i can find the parts installing it shouldnt be a problem, anyone done this upgrade, was it worth it?
    • By Steve Waldner
      I have a Kioti  Mechron utv and want to add power steering. Can anyone till me if there is an electric assist motor from a car that would work putting between the steering wheel and steering box. One that doesn't need alot of electronics 
    • By Alien10
      This is the E Brake, the one that is on the center drive shaft rotor below the dump bed. It is NOT related to any of the wheel disc brakes. 
      A few months after purchasing my Coleman Outfitter 550 (Hisun) new,  the E brake stopped working.  Thought it had got water or oil on it as it gradually went from good holding to poor holding to literally NO holding.  Been lazy using a piece of 4x4 to keep from rolling, but that's a pain.   So, into the barn I went with work light to see what the heck is wrong. E brake pedal worked, but hit a hard stop and  felt like the cable was froze up from rust but that was not the case.  As it turns out the E brake is actuated by some kind of weird actuator lever/cam arrangement based upon the actuator lever being moved about 15 degrees from its fully released position. That makes the adjustment pretty critical with such little movement.  Bolt "C" in the pic below is the adjustment bolt, held in place by lock nut "B".  Working from below, here is what I did.
      Removed the skid plate below the E brake.   6 bolts and washers.  Next, looked at the brake pads which still had a good amount of pad left on them. Looked to be a little less than 1/8" each.  Verified that the cable from the E brake pedal "A" actuated the E brake arm "D".  Cable "A" pulls and released lever "D" in the direction of the curved arrow.  Applied E brake and checked the actuator arm, it was all the way up with no bare cable "A" showing.  Released E brake and checked the actuator arm, it was all the way down with bare cable "A" showing as in the pic below. That spring pulls the lever to fully released position. Note: I disconnected the release spring from at the lever with needle nosed pliers to make working with the adjustment easier to do without that pressure on the lever.  With E brake released, loosened lock nut "B" and backed it off the lever about 1/8" or so.  Tightened adjustment bolt "C" by hand just until it stopped.  Retightened lock nut "B".   E brake now holds securely on my hillside driveway, and releases completely.  Reinstalled skid plate.  Hope this might be of some help to someone as none of this is in the owner's manual or in diagrams. 
       up.
      Released brake and rechecked the actuator arm, it was all the way down.
       
       
×
×
  • Create New...