Quantcast
Jump to content


a cooling tip

dedub

By dedub
in Joyner UTV SxS Forum

 Share

Recommended Posts

dedub Collaborator

dedub

Posted
Posted

I was going to put heater in my trooper. so I cut the hose that tees at water pump an goes back to back motor.an put shut off in it.. with it shut off motors runs about 15 degrees cooler. because that water water never get to the raidor it just goes in circle.water pump to motor. might help you all. plug that line.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • monkthumper
      2020 Hisun Sector 750 no pwr to fuel pump
      By monkthumper
      Fuel pump is good (i hotwired it) swapped relay with known good one no help. I'm leanin towards ECU but cannot find wiring diagram online. Dont know how fuel pump relay gets its signal, all fuses good, any help? 
    • Gerald Dillman
      2008 Joyner trooper transmission parts
      By Gerald Dillman
      Looking for a output shaft for a Joyner trooper t2. Went to move the buggy after sitting all winter and it appears the out put shaft that drives the rear wheels broke off inside the transmission so looking for the shaft or a complete transmission if someone has one
    • Jon Spruill
      2018 Hisun Sector 1000 Crew stalling but starts right back up. Please help!
      By Jon Spruill
      Hey Guys, I have been chasing a stalling condition for about two weeks now. The bike will crank up and idle fine, then after about 20 seconds it will fall on its face and stall. It happens at both idle and while running at various rpms. You can turn the key off, turn it back on and it will fire right back up without trouble. I have verified spark on both cylinders with a spark tester. I have also added an inline fuel filter, and pulled the injectors to verify proper pulse on each. Things I have replaced - (relearn procedure performed after each component replaced): spark plugs, ECU, relay/fuse box, fuel pump, & throttle position sensor - all with no improvement of the condition. The only warning light I get when the condition occurs is the oil lamp. The bike only has 14 miles. I am at a loss and appreciate any help and suggestions! Thanks
    • Jon W
      Havoc VS Stampede Motors
      By Jon W
      looking around and cannot find and Stampede motors, the Havoc looks to directly bolt in, with exception of the larger displacment. has anyone looked into this further? seems to be a better option considering stampede engines are on backorder. 
    • ToughLuck
      2021 Massimo MXU 1000 Runs Rich
      By ToughLuck
      I have a 2021 Massimo MXU 1000.  Last winter the front drive shaft sheared off inside the motor and it was cheaper to buy a new motor than to take it apart in order to remove the front drive shaft that was broken inside the case…
      Now it is running rich, seems to maybe be geared too high, does not accelerate well once you hit about 28mph.  I’ve replaced the O2 sensor.  MAF is next (I accidentally ordered the wrong one, but when I removed the old one you can clearly smell fuel).  
       I’m not a motorhead but I can turn a wrench.  Any ideas how to get this motor optimized?  The motor has about 300 miles on it.  I broke it in as recommended in the manual. 

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...