-
Similar Topics
-
By robwork9
Hopefully someone out there is a T-Boss 410 electrics expert or a Massimo mechanic is viewing this. I parked my 410 and it was working great. I came back a week later and attempted to crank it and nothing. Turned the key and no power. Figured it was a bad/low battery so I charged it. Still nothing. Attempted to jump start it and still nothing. Usually when I put the key in and turn it to the first position, the display comes on and I hear the ECU and other items boot. Now it is doing nothing.
I slowly went through the electrical system and found the main fuse attached to the starter relay, part 71602 (pic 1) blown. I figured replacing this fuse would fix my problem. It didn't. I then ordered a new starter relay thinking maybe that part had gone bad and caused the fuse to blow, but a new relay did not fix the problem.
I have found a work around for starting the machine. If I take one of the purple/black leads (pic 2) and insert one of them in the bottom right of the starter relay (pic 1 and 3) then the machine will get power even with the key in the off position. I'm bypassing something but don't know what. I can use my right hand to hold the wire against the lower right of the starter relay, reach over and hold the brake with my foot, then take my left hand and turn the key and it will crank. As soon as I remove the wire from the relay the machine shuts down. I have even removed the power distributor box and it will still get power when I touch the wire to the relay. Of course this is not the way it should work but if I can't solve this problem somehow I may just have to rig a connector to the relay and bypass whatever is causing the electrical issue. Massimo has told me the purple/black wires on my model are not used.
Any help in figuring what my problem may be or other items I can try?
v/r,
Rw
-
By cliffyk
I had mentioned in a previous post that I had removed the front anti-roll bar from my 2020 Outfitter 400; I ran that way for a month or so without noticing any downside however recently I installed a 'suicide knob" (see below) to assist my Parkinson's disease affected arms in turning the beast--but after doing so i found that in the quicker, tighter turns the knob permitted the vehicle would nosedive a bit, dig in, and plow on hard surfaces--not scary, but quite noticeably.
So I put the bar back on. Then today I got about 1-1/2 miles down the main road on the nearby power lines, turned around and came home to take it off--with the bar on, at 25 to 30 MPH, the front-end of the beast jumped like rabbit at each bump in either wheel rut., for a nearly brutal and quite uncomfortable ride. the bar (20 mm solid steel) is far too robust for the weight of the vehicle. The front bar on my 3900 lb. Infinity M37 is 30 mm...
suicide knob--for you younger folks:
-
By CYJSP2009
Hi All,
Joyner 650 commando rear differentail and its parts are avaialbe now.
Qty is limited. Any one who is in need please contact [email protected]
Thanks
-
-
By CYJSP2009
Hello Everyone
Brand new Joyner CV AXLES are waiting to be unloaded at LA port and then be sent to warehouses in Charleston, TN , BALTIMORE, MD and Groveport, OH. Estimate they will be available for shipments to end customers in about 2-3 weeks.
These CV AXLES are ordered in February this year and now it is middle July. Very long time to get these parts. Qty for each model is not big. Detail as below:
S/N Part No. Description Charleston, TN BALTIMORE, MD Groveport, OH Total
1 D650.03.02.02.00 650 Sand Spider Rear left 3 2 3 8
2 S650.03.02.02.00 650 Commando Rear 7 6 10 23
3 TR1100.03.01.03.00 TR1100 Front 3 3 4 10
4 D650.03.02.03.00 650 Sand Spider Rear Right 3 2 4 9
5 S800.03.02.02.00-R2 800 R2/4 Rear Shaft 4 4 6 14
6 TR1100.03.02.03.00 TR1100 Rear 6 5 9 20
7 S650.03.01.02.00 650 Commando Front Left 3 3 4 10
8 S650.03.01.03.00 650 Commando Front Right 3 3 4 10
Below items are also available. These items can be shipped in days
CAGE:
1. 800 Renegade R2/R4 Front outer cage --- 5 pieces
2. 800 Viper SV1100 Drive shaft rear Left outer cage --- 5 pieces
3. 800 Viper SV1100 Drive shaft rear left inner cage --- 3 pieces
CV BOOT:
1. 650 Commando Left Front / 650 Commando Right Front /650 Sand Spider Rear Left / 650 Sand Spider Rear right / OUT CAGE 2 pieces
2. 650 Commando Rear OUT CAGE 1 pieces
3 Trooper Front / Trooper Rear / 800 R2 R4 Rear OUT CAGE 2 pieces
4 650 Commando Left Front / 650 Commando Right Front INNER CAGE 1 pieces
5 650 Sand Spider Rear Left / 650 Sand Spider Rear right INNER CAGE 1 pieces
6 650 Commando Rear INNER CAGE 1 pieces
7 Trooper Front / Trooper Rear / 800 R2 R4 Rear OUT CAGE INNER CAGE 2 pieces
Anyone who need above items please contact me at [email protected] Thanks.
Other Joyner items needed, you can also contact me and I will try to help.
Have good day
Casey / Leaf Asia
2021-07-20
-
-
-
Gallery Images
.jpg.7db75608d6304a0b1453655b7c0267cd.jpg)
![ry%3D400[2]](https://www.utvboard.com/uploads/gallery/album_29/sml_gallery_475_29_6335.jpg)
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.