Quantcast
Jump to content

2014 XUV 825i Shifter woes

kevindsingleton

By kevindsingleton
in John Deere UTV SxS Forum

 Share

Recommended Posts

kevindsingleton Newbie

kevindsingleton

Posted
Posted

I bought a 2014 XUV 825i back in the spring/summer of 2014, and have been enjoying it on my property. One problem has cropped up, though, and that is that it is sometimes very hard to shift from reverse to Hi, and back again, especially for my wife and others who don't drive the vehicle, often.

From what I can tell, something has changed in the adjustment of the shifting mechanism, probably someone pulling too hard on the lever. The shift lever now doesn't go all the way up to the reverse position, and the transmission will sometimes pop out of gear when going forward, in Hi, especially under load (uphill, etc).

Does anyone know the proper method for adjusting the shifting mechanism?

Thanks.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Ermd ttk
      UTV Odes Ravager 1000cc - Strange noise from the back
      By Ermd ttk
      Hello friends,
      I got my ODES Ravager UTV yesterday and after a couple of hours of driving when I go downhill I heard a strange loud noise a couple of times, like a gear skipping or maybe something from the differential.
      It doesn't always happen and when it does it is heard for a few seconds and then it goes away and everything works normally, I'm worried if there could be some major malfunction or what could be the problem if someone can help me?
      Thanks a lot.
       
    • lonerider98
      2013 UT 500 won't go into reverse.
      By lonerider98
      At the end of last year my Coleman UT 500 will not go into reverse. I can hold it over toward the reverse to move it nut it won't lock into reverse. Anyone have this problem? Winter is just about over and going to have to get this resolved. Thank You!
    • skittle021
      Super Weird Problem with Primary Shave/Clutch...
      By skittle021
      So I've got a Hisun 550 that I was doing some work on that required removing the CVT and it's housing. Upon attempting to reinstall the clutch, sheaves, etc, I found that the belt no longer fits - it's far too wide. None of the parts have been replaced, they're all OEM. Exactly the same parts as what I took off a few weeks ago.
      To be more specific, my belt is 1.25in wide, but the gap between the clutch and the primary sheave is only 7/8in wide. I'll include a few photos to explain.
      Has anyone ever experienced such a bizarre problem? Any help at all would be appreciated, I've been stuck on this for a month. I'm open to just about any suggestion.
      Photos: 
       





    • packersfan
      Hisun 500 very hard to turn
      By packersfan
      I have a hisun 500 got from a auction and when turning a corner left or right it's a two hand job then when you left go snaps back.any help on what to look at would be appreciated.
      Also blows blue smoke until she gets warm then it's ok 
    • alevins
      2008 HS700 reverse rev limiter
      By alevins
      Good day all, 
      searching here but cannot find the answer,  Hisun been working fine and now reverse limiter seems to be engaging and cannot back up, cannot find a clear solution to disable the limiter. found a possible relay?  not sure which one or to cuut a wire at ecu but a picture or diagram would be helpful
      thank you for any help in advance

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...