Quantcast
Jump to content


I need help not getting fire on my trooper

Jarrettj88

By Jarrettj88
in Joyner UTV SxS Forum

 Share

Recommended Posts

Jarrettj88 Contributor

Jarrettj88

Posted
Posted

I have a joyner trooper think 2007 model 1100cc and it will turn over but not getting any fire. Put new coil on it new crank sensor and when I check the plug going to my coil pack with test light it shows that it don't Have power and seems to be saying there's no ground either. Mine has 3 wires black,white,and orange

Jarrettj88 Contributor

Jarrettj88

Posted
  • Author
Posted

[email protected] and any suggestions on what to do is there any way to bypass the computer or anyway to straight wire it? And is there a kit to swap it over to a carburetor? I just really need to get it running I bought it already messed up and just want to get it running asap without wasting a lot of money on it any help would be greatly appreciated thanks

Jarrettj88 Contributor

Jarrettj88

Posted
  • Author
Posted

[email protected] and any suggestions on what to do is there any way to bypass the computer or anyway to straight wire it? And is there a kit to swap it over to a carburetor? I just really need to get it running I bought it already messed up and just want to get it running asap without wasting a lot of money on it any help would be greatly appreciated thanks

Kinarfi Veteran

Kinarfi

Posted
Posted

Where do you live, if you fill out the profile, we can get to know you a little better. Maybe some one lives just around the block from you.

You say it was messed up when you bought it, did it ever run for you?

Welcome to UTVboard

Jeff

Kinarfi Veteran

Kinarfi

Posted
Posted

Here;s and idea for you, set your Fluke to measure current and see if the computer is putting our a signal to them and then do the same to the ignition coil. while measuring the current, push the frequency button, if you get a frequency, see what the duty cycle is. This should tell you if the CPU is go or not.

Jarrettj88 Contributor

Jarrettj88

Posted
  • Author
Posted

Finally got spark to my wires dunno if anyone has had this problem before but it was actually my switch some how if you turn it all the way to the right if went to far and dunno why but wouldn't send anything to the coil. So if I turn it slightly back to the left a hair it started hitting. So now guess I have to try new plugs and drain the gas a refill it to see if it will start.

Sent from my SM-G900V using Tapatalk

  • 4 years later...
  • 11 months later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Popular Now

  • Similar Topics

    • rdc
      Looking for the left side shaft carrier where the rear bearings go for a 2014 1100cc sand viper, I understand an 800 cc carrier will also work.
      By rdc
      I posted this before , but I had the year wrong. The part I need is for a 2014, I don't know what all years will work, but I need the 2 bearing style with the spacer in the middle. It looks like this pic. If anyone has one I'll buy it rite away. my email is [email protected]. Thanks, RC

    • rdc
      Looking for a left rear shaft carrier (just the carrier) for a 2007 Joyner 1100 sand viper
      By rdc
      Hope I posted this in the right place. Looking for the left side shaft carrier where the rear bearings go for an 1100cc sand viper, I understand an 800 cc carrier will also work. I need the old style two bearing with the spacer in the middle, the new style with just the one wide bearing wont work. If anybody has one I'll buy it right away. my email is [email protected]
    • MilSurpYinzer
      New Mexico etc
      By MilSurpYinzer
      I heard there's several off road festivals out that way. One or two post apocalyptic, the rest just rev and run. Anyone know a good one that offers camping? Any advice for out of state people like hauling, legality, and where to stay?
      Ideally me and the missus would be down for camping out and setting up shop somewhere nearby. That way we can just wake up, load up, and ride.
    • Burk
      2021 Axis(Hisun) 700 Will not fire up
      By Burk
      I have a 2021 Axis(Hisun) 700 from Lowes. Will not start. Checked starter, solenoid, spark plug and fuel pump. Everything seems to be fine. The motor turns over and will try to start but just will not. Battery is also good. Frustrated!
    • 180gtr
      Parting out Joyner Sand Viper 1100
      By 180gtr
      Parting out a rolled Sand viper 1100. I will list some of the parts I have, otherwise ask me if there is something specific you are looking for. I am selling everything I have for $800. I am located near Glenwood Springs CO.
      SOLD ITEMS, I do not have these items.
      Wheels
      Tires
      Engine
      Transmission
      Axles
      Shocks
      Control Arms
      Things I have....These all came off of the running engine. I have video of it running if anyone needs to verify that.
      Throttle Body $90
      Starter $150
      Alternator $150
      Fuel rail, injectors, fpr $100
      fuel pump $70
      Map Sensor $50
      Full set of Guages $150
      Exhaust w cat, O2 SOLD
      Ignition Coil - SOLD
      Wiring harness and ecu SOLD
      Radiator, shroud, elec fan, overflow tank $200
      Fuel tank w sender $150 Has dent at base of fuel neck, no leaks
      I have a box full of misc bolts, nuts, etc.
      I will sell the Chassis or Frame alone for $200. The chassis is in pretty good shape, needs some cage repair and 2 areas straightened where control arms mount. If anyone had an automotive frame machine it would take a few hours.
      That would include....
      Brake calipers, lines, pedal, master cyl, E brake assy,
      Steering shaft, wheel
      Ignition switch, key
      Light bar frame, 2 lights
      misc hardware, spindles
      2 hubs, rotors
      Engine mounts
      Throttle pedal, cables
      Shifter, cables
      Clutch master, pedal
      I am sure I am forgetting something.
      I am parting this out of ebay right now, I just picked up another project and could use the room. No I will not take less than $700 for all of it or $200 for the frame. I do not need to sell it, I will make far more parting it out but would like the extra space in the garage.
      If interested I also have an 07 1000rr engine setup I would sell with the buggy for $650.
      Thanks!
















UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...