Quantcast
Jump to content


Recommended Posts

Posted

When starting the 800 it will go to 2500-3000 rpms. I do the 3 times re-set on key switch then start. Sometimes it corrects and starts fine. Later in the day it wil do it again. Replaced throttle block-all clean. No change. Any thoughts?

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By Tim n Deb
      Riding out today it acted like it ran out of gas,  stalled and died and would not start.   Towed back to house,  New  plug added this past month,  plenty of oil, getting plenty of gas, battery cranks good.   Trys to kick in and starts but doesnt.   Two days prior while sitting at a idle it died.  Added gas and it started did my ranch chores with it.  But just now it stalled out cranks but will not start.   Tried to find if fault codes came up on the clock like manual says but not sure I am doing that right.  Any and all help apprecated.  Thank you
    • By Joe Breaux
      Decided to do an oil change on the Massimo ...drained oil, screen was very clean even tho oil wasn't.  Then went to remove old filter.. holy crap ..I tried every tool I have, could not budge it..Went to store and got one of the end cap type..fit nice and tight, put a 1/2 in drive ratchet on it..nope..not moving.  Put a 18 on breaker bar o. It. The inside of the removal tool broke off!!  Had to weld it back together. Put a pipe on the bar for more leverage.  Finally broke it loose..
      I have never seen a filter in my 55 yrs of working on engines so tight..And i was the one who put it on 2 yrs ago.  JUST HAND TIGHT!
       
    • By KWinTX
      I just bought a new 2024 Hison 550 Stryker 2 months ago. this is the second time I have had this issue.  It only has about 20 hours on it. The last time it happened we took it back to the dealer. it was a fuse.  Since we live three-hour time driving there and back. I would like to find another solution if possible.  I have tried all the fuses that seem to have anything to do with starting.  Currently checking the battery. The battery is new. it came with the unit. It is probably 6 months old.  the UTV has all power to everything electrical. lights turn signals and radio all work.  When trying the key to start . it is 100% dead. as in it doesn't even click.  There is a low whirring like the fuel pump is turning on though. The Unit was running and driving just fine.  we shut it down for the night. The next morning my wife found it in this condition.  Thanks for any Ideas or solutions???   Otherwise, it goes back to the dealer tomorrow. Just hope I didn't buy a lemon. Great little UTV when it does run.😅  anyone else ever have this Issue..? 
    • By GunnersTacklebox
      Hi All,
      New here, but bought a 2022 Sector 750 brand new last march (old stock up here in Canada)
      It's a good bike so far, but I have noticed a quirk and was wondering if anyone else has had a similar issue?
       
      The issue I've had is if I leave the utv parked on any incline, not even a major incline, and leave it to sit for a while (day or two) it will not start properly. It will turn over and not fire until I press the gas pedal, when it will run and rev up, but if I let off the gas it will die. It will keep doing this until I either start it in gear and drive it for a bit or leave it in neutral and roll it down the hill to flatter ground. where it will have to sit for a while. 
      If I park it on a decline there is no issue. fuel is not low, it's occurred a couple times now. 
       
      Any thoughts on the cause of this? Dealership just says bring it in and let them take a look, at my expense of course. 
    • By Mike Jenkins
      I have a 2013 Hisun with a 686 Yamaha engine.
      I purchased it from an individual and it ran fine as long as the battery was full.
      I replaced the stator and now it will not start (run).  It cranks fine, has fuel pressure, but will not fire up.  I replaced the coil, no luck there.
      a technician told me that it was the wrong stator and wants a mint to replace it.
      the wires all plugged in when I installed the stator.
       
×
×
  • Create New...