Quantcast
Jump to content

Sign in to follow this  
utvman

DMP Dressup Kit

Recommended Posts

The kit retails for 114.99 we welcome new dealer programs, the kit is for 04-07 Yamaha rhino bed and dash kit, all hardware is polished stainless with anodized washers, the aluminum plain washer is polished, The colors available gold,purple,blue, red, black, polished aluminum, custom colors are available upon request. We also offer roll bar [...]

View the full article

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Sign in to follow this  

  • Similar Topics

    • By johnpeter
      2016 Yamaha YXZ1000R On Ebay
      https://www.ebay.com/itm/2016-Yamaha-YXZ1000R-Side-by-Side-UTV-1400-Miles-Windshield-Wipers-Here-YOU-GO/114423845643?

    • By dalerio007
      i have a 2017 cub cadet challenger 750 camo, after a month of nonstop work with the pandemic i was finally getting a chance to ride it. it would not start, the battery was dead, went to charge the battery and noticed a mouse had chewed a yellow wire one of2 going to a block of some kind in battery box, it is tied into the 2 fuse relay breakers  attached to the starter relay. there is a red with stripe wire that goes to a harness below the rectifier in engine compartment, it has no power to it with multimeter and the fuse block is getting real hot. other than that the dash lights up, but no readout and the gauges dont cycle, the fuel pump does not start. on the fuel pump i checked the red wires to the cdi and both have contact and are intact but one does  not have power when the key is on and there is no spark  i tried starting fluid. i have swapped out the cdi from my cousins  same year and model, also the ecu and the main relay. i have no idea where to look now. his has broke the shim again and will not start. also i did notice that i wiggled a wire connector going to a sensor on the engine and a couple lights came on on the dash, the stirring wheel one and check engine but only did it once and i cant get it to do it again. i have looked over the harness for anymore damage and have found none.
      has anyone seen this problem before, is it wiring? ground? what do i need to check next. the place i bought it has no service the guy said he could only swap parts and try. sent me to another place over an hour from me  and that guy on the phone said he was covered up and didnt know when he could look at it so he must be busy lol. besides i dont want to have them charge me $3000 to replace everything on it before they get going.
      my advice is do not buy a cub cadet, we thought we were getting a cub cadet and it turns out it is a cheap chinese pos. i still love my cub but wish i had known this before i bought it and i would not have.
      any help would be appreciated thanks
    • By Overlander
      After turning 2 batteries to water over last winter, I found that my digital dash display is staying on with the key removed. I was originally thinking the issue originated from the ignition cylinder but I'm now thinking its the ECU controller box under the hood. One of the unserviceable relays is making a weird sound when I remove the key. I have both batteries up to full charge and discovered the display issue last week when I saw the lights on in the dark.. Do any of you have any input on this issue? Ignition or controller.. Any help before just ordering parts would be helpful  The controller is $140  not sure on the ignition.. Thanks in advance..
    • By Wilkie
      Hello all,  I have a yamaha rhino 660 with 156 hours on it. Just acquired it. It has anedelbrock carb and aftermarket exhaust. Anyone know how to adjust an edelbrock? Also, machine smokes like crazy. White smoke. So i need to get the carb sorted out and then see if its a bead gasket r valve guides causing the smoke I cannot find u h info online about the carb so any help is
      muCh appreciated. 
    • By Mike Cole
      Is there someone that makes them and doesn't charge so much? Need some for mine.


×
×
  • Create New...