Joyner,Renli,Reeper,Rebel,Oreion SideXside and 2 wheel drive
-
Similar Topics
-
By Steve Vanvelzen
I Recently purchased a Massimo T-Boss 550F last fall with their 60" snow thrower because I couldn't find a decent UTV here in Southern Ontario; nothing in stock anywhere. I am having really bad buyer's remorse after spending time on it and reading all the bad online reviews. The company boasts the fact that it is built in Texas, USA, so I was hoping to do the right thing by buying, "Made In North America" but it is still Chinese Junk, assembled in the USA. and I am starting to realize that I am going to have a lot of difficulty getting parts for this thing; I can't even get an oil filter, finally bought a "Hisun" filter and hope it fits. i busted the shear pins in the snow thrower and can't find replacements for that either. The thing is so hard to change gears most of the time; I am terrified I am going to wreck something. The place I purchased it from is absolutely useless. Can I adjust something myself? Anyone out there have this problem and have some advice (besides selling it and buying a good brand)?
-
By Earthscum
Hi, I'm a mechanic and am at a loss for a customer's 2021 UT400. This thing only got used for the end of the summer, only has 3.3 hours on it.
So far I've found:
No start - starter switch works, relay in relay/fuse box clicks. Solenoid is operating as it should, no signal to solenoid to start. Starts and runs when I hard-jump the solenoid.
No F or R lights on dash - N lights up, and goes off when shifted into either gear
No brake lights - tested switch, it works as it should
No turn signals
Parking brake light is on - switch is working correctly, doesn't change status
All connectors are secured, no wires look out of place. I have an incredible dislike for HiSun equipment. Every one I've dealt with has been full of gremlins. Has anyone else had any issues like this? Would this be something wrong with the dash? Or the relay/fuse box? or both? I don't want to contact Coleman and have them send a bunch of stuff that won't fix it, especially with how long electronic stuff takes to get these days. The last warranty I did for them was a go-kart that shelled the drive shaft bearings and it took 4 months for them to send us the parts.
Any help or knowledge would be much appreciated!
-
By 2018TEXTRONHL
Looking for the truck bed components 2018 Textron 900 Stampede. There is limited information available for the assembly. Might need a parts list.
Tim
-
By Hisun .500
So my hisun 500 is tore up and all the wiring is wasted i was wondering can i pull out all the wiring and just put in the. Basics .please help
-
By erickat
I have an American Landmaster LM500 with an old style snow plow hook-up. Unfortunately, the mounting bracket broke & I lost the key part where the plow receiver connects to the cross bar with two pins.
I checked with customer service & they said...
On Monday, January 10, 2022, 03:25:29 PM EST, Feedback <[email protected]> wrote: Sounds like it may be the old style push tube universal mount system, it looks like those have been discontinued but we may still have some back there. I believe they are sold as a kit though and they are not cheap, part # 15329. I’ve included a photo below since the web store does not have a photo for that part.
https://americanlandmaster.com/search/results?keywords=15329
I checked with our parts department and neither the kit or the components are available as that was the older style hook up system. The only option at this point would to have something manufactured. All of our current plows are either dual actuated or winch hookup so we would only have components for those models as of currently.
In the picture, below, it would be item #5 (the one with the two mounting brackets that hold the pins that the plow mount latches onto) - not the top one in the picture, but the one below t hat.
I have all the other parts - but the missing part is critical to mounting the plow.
Does anyone happen to have an old one they could part with - or have an alternative solution?
The rig wasn't optimal, as you had to use the winch to raise & lower the blade & manually adjust the angle. It kept falling off when I was plowing snow - as the pins that hold it in only have a groove for a pin clip & they would often get knocked off & then the plow would hang down & you'd loose the pin - then it would get all messed up.
Thanks in advance for any advice. I am thinking of going to a welding shop to see if they can create something - but it will still have the same limitations as before - the pins are highly specific and not cheap
15331 Pin, Shear Univ Mount Blade PART #: 15331
-
-
-
Gallery Images
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.