Quantcast
Jump to content

sigh


Travis

Recommended Posts

I finally decided to take the carburetor off the mule and clean it,

Pull it off, piece of cake....

Take off the bowl, here is what it looked like.IMG_20191129_110850.thumb.jpg.c711cce70885b7eff4bf6fd113fbf62c.jpg

 

Then I proceed to pull out the float pin, sigh 

IMG_20191129_112003.thumb.jpg.f479aa6aee72d93cdd7fd93b74e83eaa.jpg

As you can see, part of the hinge casting broke off.

I contemplated JB welding it, but decided not too.Mikuni and Kawasaki are $170-$200 too proud of this carb.

I stooped low and bought a  $60 off of amazon.

Is rather go oem but couldn't in this case.

 

Oh well, nearly 20 years on 1 carb. not bad i guess. never took apart and cleaned, just b12 chemtool in the tank every so often.

Link to comment
Share on other sites

Yep, for the 550, a OEM mikuni is $170+

$60 seemed to be reasonable. I saw some for $30, or less but I really question the quality at that point.

Interesting thing I noticed, I'm used to Briggs carbs made by Nikki or Walbro.

This Mikuni uses a metal needle with a rubber tip instead of a metal needle and rubber seat.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By Mark T
      MY 400 is gutless. I would like to know if I can upgrade to a larger engine ?
    • By great8redsfan
      Okay folks. I have a low power issue. Been like this for a few years. Place I work at bought 3 and all have lost most of the pulling power.  They gave them away after local shop worked on one for 3 months and it had great power for about 1 month and then crap. They replaced throttle body, fuel injector, spark plug and IAC motor. Seat belt switches have wires cut and left open so no seat belt warning light anymore. It revs to 6k rpm in neutral but when put in gear and take off in low it just doesn’t seem to want to go anymore. Running 93 octane fuel with Stabil.  Any ideas greatly appreciated. I dont have a scan tool but no codes on dash. If held to floor it pops a little and runs almost 5K rpm but if I let off pedal about an inch it smoothed out and revs up to 6k rpm. 
    • By Travis
      View File Kawasaki Mule 550,520,500 Complete service manual
      This is a complete service manual for the Kawasaki Mule 500,520 and 550 models.
      Topics  covered include Brakes, Steering, Electrical system, suspension and fuel system. As well as engine repair procedures and Transmission/Final Drive procedures.
       
      ********************************************************************************************************************************************************************************************
      If you need more information about the engine this manual linked below is chock full of information.
      Thanks goes to @cliffyk for getting these files all  into one PDF format for uploading.
      Submitter Travis Submitted 04/18/2021 Category Kawasaki  
    • By johnpeter
      2023 Can-Am Maverick Sport XMR 1000R RED TITANIUM On Ebay
      https://www.ebay.com/itm/156096225938?

    • By johnpeter
      2023 Can-Am Maverick Sport XMR 1000R RED TITANIUM On Ebay
      https://www.ebay.com/itm/156096225938?

×
×
  • Create New...