Ferguson Fabrication Inc is shutting down gracefully
-
Popular Now
-
-
Similar Topics
-
By Tommy2bits
Just bought a brand new 2022 (NOS) Sector E1 with Lithium upgrade. (Single 135ah/200amp continuous). I've climbed a moderate hill in my woods probably 20 times since buying it. Today It won't climb it unless I am in Low. In High it almost makes it and then completely dies and I have to roll back down the hill. In Mid range (Max Range) I can't get 2 feet up the hill and the power output in only 100 amps, I have climbed this hill in every speed before many times. I put it on the trailer tonight and it wouldn't even get on the dang trailer in mid range. Torque is gone. That being said, when I am just cruising around in Midrange, it runs absolutely perfect with plenty of power. The only thing I did was charge it up, that is all. I charged to 100% using the charger that came with the battery. Before you think the BMS is shutting down due to overcharge protection, remember I am going UP hill so there is no regeneration AND I have done it before at 100% charge AND another big problem is that after 1 mile it is already down to 85% so it's not over charging and why is the battery draining so fast when I got 27 miles before. Battery output is fine in Low it pulls 200 amp up the hill just like normal so that doesn't point to the battery being the issue. All the individual cells on the battery are in line, so there is no dead cell either. I am tech savvy but to toward electric motors and I tried to cover all my bases. Please don't tell me basics like torque is reduced in High and Mid. The only thing I can think of is that I smelled something when I took my first drive today and I thought it was the Ebrake dragging but there was the correct amount of play in the cable and I jacked up the rear wheels and they spin freely. maybe something burned out in the motor, I do not knowm still runs great, we'll see if I have any trouble on the hills at the lake house this weekend. Maybe this is "Normal" and the settings were off before and was giving equal torque for whatever reason instead of 50% in Mid and 70% in High like the manual says....
For reference....this is it not even able to get on the trailer in mid range
-
By dryvalleyboy
The steering shaft is slipping,I checked it's tight as the bolt will take at the u-joint.. Is there a slot or something it may have jumped? This is right after the shaft enters the area under the hood.Thanks.
-
By 2coil Fox
SO NOW what do owners do? I own a 2021 Tracker SxS 800SX LE —— perfect condition and very pleased with it BUT concerned that Textron discontinued building them ! What are other Tracker Off Road owners hearing & doing for Service etc..?
-
By KevinCO
I have a Polaris 900 side by side that I want to haul in the back of my full size pickup and still be able to tow my camping trailer. The problem is that, although the side by side fits completely in the truck bed, the curvature of the rear tires stick out enough that I can't close the tailgate. I cannot tow the trailer with the tailgate down, and I don't feel safe just removing the tailgate and relying on the tie-down straps to keep the utv in place. They always bounce around a little and it would really suck having it bounce enough to slip out between the truck and trailer. Any thoughts on a solution to this? I also don't feel comfortable towing a flatbed trailer behind my camping trailer. I've thought about getting a tailgate net to replace the regular tailgate, but I don't have any experience with them. Suggestions would be greatly appreciated.
-
By FTG-05
I want to ditch my Kubota RTV-XG850 and its moronic twitchy throttle design flaw, get rid of the problematic engine and the 40 mph purposely throttled speed.
So far, I'm looking at the Honda Pioneer 1000 and the Polaris Ranger 1000, both of which have 1000-1500 lb payload bed capacity.
What other makes and models should I be looking at?
Thanks for the help!
-
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.