Quantcast
Jump to content


Recommended Posts

Posted

Hey all,

Took my Hisun sector 750 into the dealership to get a couple warranty issues resolved ( Stator died, parking brake alarm stuck on and occasional no start without throttle being applied).

The unit was at the dealership for 5 weeks, and when I went to pick it up it had more issues. Went to start it to load it up and the starter was making a terrible grinding noise. Turned it off to see if it was a one time fluke, and after then engine shut down there was a few loud clunks from the engine area that I had never heard before. Neither issue was present prior to the shop working on it. 

Needless to say I left it there to be looked at again. Kinda peeved since it's a couple hour round trip hauling a trailer, not happy on gas. 

Any thoughts on what could have happened? More concerned about the clunks as opposed to the starter grinding. 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Popular Now

  • Similar Topics

    • By AaronD1982
      Next problem with charging system to tackle, any help would be appreciated.
      New starter solenoid....check
      New Voltage Regulator...check.
      Dynamic test to Stator.....bang...pulling like 2 Volts AC
      Problem: Without pulling the part out and stranding the vehicle at the shop forever.... I am trying to find the correct stator or at least one that might not be exact for the Massimo Buck 400S, but fit and connect and do the job if that makes sense.... if anyone has any ideas, please shoot them my way.
    • By BWF
      I have a 2011 or so Landmaster LM200.  I cannot get it to start.  I turn the key and nothing happens.  The brake switch seems to be working, the ignition switch works.  The Coil is new the Voltage Regulator is new and the starter relay is new.
       
      I can connect the terminals on the starter relay and it starts right up and runs fine.  I just can't get it to start by turning the key.
       
      I am having a bit of trouble bleeding the brakes, not much fluid comes out at the calipers when I am pumping the brakes, though that an air bubble near the brake switch might make it not sense that the brake pedal is depressed.
       
      I am at a loss, please help!
       
      Brad
    • By esmarkey
      Hi, I purchased a used Cub Cadet 750 Challenger that seemed like the belt was slipping so I put a new belt in.  It still acts like the belt is slipping but now I am thinking it is the clutch? 
      What is the best way to remedy this problem? 
      Can the clutch be rebuilt?
      Are there aftermarket clutches available? 
    • By Burk
      I have a 2021 Axis(Hisun) 700 from Lowes. Will not start. Checked starter, solenoid, spark plug and fuel pump. Everything seems to be fine. The motor turns over and will try to start but just will not. Battery is also good. Frustrated!
    • By HISUN Sector 750 EPS Failu
      "Mrs. Smith" doesn't like how loud our Sector 750 is.  On a HISUN forum someone said the same thing about his 750.  I haven't given it much thought because I've been more focused on stuff that has broken.
      So, I used my decibel meter to check ours out.  4000 RPM, Low gear, under 20 MPH . . . . 97 decibels.  That's above most ordinances, even state boat noise limits.
      AI Overview Ninety-seven (97) decibels is considered very loud and dangerous to hearing with prolonged exposure, roughly equivalent to a newspaper press, a loud nightclub, or a snowmobile. At this level, damage can occur after just 30 minutes, necessitating hearing protection
×
×
  • Create New...