Quantcast
Jump to content


2015 Massimo 500 idles really high

Andy

By Andy
in Massimo UTV SxS Forum

 Share

Recommended Posts

Andy Newbie

Andy

Posted
Posted

I have a 2015 Massimo 500 that idles really high and it will not let me shift into gear while it's idling. Not sure where to start. Also it will bog down and stall constantly. Starts right back up everytime. Advice please. 

Travis Grand Master

Travis

Posted
Posted

I don't know a whole lot about these Massimo brand, but it could be 2 things, a vacuum leak, causing excess air to enter the combustion chamber, or it could even be a electronic issue.

The bogging makes me think it's more of a vacuum leak, how I find vacuum leaks is I get a bottle of WD 40 in a trigger Pack, not a aresol can. And with it running spray around the injectors and lines and if I spray it in a certain spot and the engine speed changes, that's where it's leaking.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Popular Now

  • Similar Topics

    • AaronD1982
      Massimo Buck 400S UTV Stator......?
      By AaronD1982
      Next problem with charging system to tackle, any help would be appreciated.
      New starter solenoid....check
      New Voltage Regulator...check.
      Dynamic test to Stator.....bang...pulling like 2 Volts AC
      Problem: Without pulling the part out and stranding the vehicle at the shop forever.... I am trying to find the correct stator or at least one that might not be exact for the Massimo Buck 400S, but fit and connect and do the job if that makes sense.... if anyone has any ideas, please shoot them my way.
    • rdc
      Looking for the left side shaft carrier where the rear bearings go for a 2014 1100cc sand viper, I understand an 800 cc carrier will also work.
      By rdc
      I posted this before , but I had the year wrong. The part I need is for a 2014, I don't know what all years will work, but I need the 2 bearing style with the spacer in the middle. It looks like this pic. If anyone has one I'll buy it rite away. my email is [email protected]. Thanks, RC

    • Fmaxiron
      Honda Pioneer 1000-6 back windshield or screen.
      By Fmaxiron
      I just purchased a 2023 Honda Pioneer a couple of weeks ago and had the hard roof and a front Honda Pioneer windshield installed at the shop before taking ownership. As things are drying up here in NC, the grass and dust are beginning to fly right through the back of the cab while driving. I was wondering if anyone has any good recommendations on rear windshields, dust panels, or mesh screens to help stop this?
      Thanks a lot!
    • carbdoctor
      2023 massimo 850 eps overheating
      By carbdoctor
      I have an 850. It’s been overheating. The electric fan is not kicking on. I see the temperature switch going into the radiator, but there’s no wire plugging in to it or none to be found in the area. i’m thinking I might’ve hooked on a branch and it ripped out the harness on that part. Does anybody have a picture or no where that plugs into on the harness? On the top of the firewall, I did notice some plugs that have nothing plugged into it. I was wondering if it’s a harness that goes from there down to the radiator that was pulled off


    • BWF
      Landmaster LM200 Will Not Start
      By BWF
      I have a 2011 or so Landmaster LM200.  I cannot get it to start.  I turn the key and nothing happens.  The brake switch seems to be working, the ignition switch works.  The Coil is new the Voltage Regulator is new and the starter relay is new.
       
      I can connect the terminals on the starter relay and it starts right up and runs fine.  I just can't get it to start by turning the key.
       
      I am having a bit of trouble bleeding the brakes, not much fluid comes out at the calipers when I am pumping the brakes, though that an air bubble near the brake switch might make it not sense that the brake pedal is depressed.
       
      I am at a loss, please help!
       
      Brad

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...