-
Similar Topics
-
By didgeridoo
Hello, All! I've decided to replace the traction batteries in my 2018 Sector E1 with a 48V Lithium set. They may be expensive, but I figure the Discovery Dry Cell are, too. I am not looking for the max driving range, as I have never received near the brochured range to begin with, but a good mix of charge/ get work done/ charge is what I am expecting.
I have settled on the 48V EAGL kit from bigbattery dot com. Each battery pack provides 30Ah. The kit ships with a charger, as well. The packs would be physically connected in parallel (using a busbar) to one another, maintaining the 48V voltage, but together would be able to provide the amp draw the buggy pulls when going up hill or towing a rake (rated 320 max continuous Amps). This is in comparison to the serial connection the eight 6V lead batteries. Each of the EAGL batteries looks to have its own BMS; am I correct in thinking I will have to use their included charger rather than (simply) changing the onboard charger to lithium mode? The chemistry of the pack is LiFe PO4, for what it's worth. I haven't torn anything apart yet (to diagram), so I am not sure how the dash will interpret the AMP draw, but the kit I am looking at includes a dash mounted charge indicator.
If anyone has completed a similar conversion, do you have any tips? Specifically, how did you remove the original batteries, and how did you secure the new ones? I am guessing that almost any change from the stock batteries would involve at least some modifications. Any tips would be appreciated, especially things I may have failed to consider. Thanks!
-
By Hoppy one
I replaced the stator on our Bennche 500 because it was not charging. It ran as long as you kept the battery charged. I replaced the stator now it’s not firing. The only problem I found was a wire in the new stator for the crank position sensor was in the wrong place in the plug. I switched it around but still no fire. Putting a meter on those wires and cranking the motor showed no voltage from the crank position sensor. Something I did or a bad “new “ part? Thanks for any ideas.
-
By MilSurpYinzer
I heard there's several off road festivals out that way. One or two post apocalyptic, the rest just rev and run. Anyone know a good one that offers camping? Any advice for out of state people like hauling, legality, and where to stay?
Ideally me and the missus would be down for camping out and setting up shop somewhere nearby. That way we can just wake up, load up, and ride.
-
By RBonds007
I bought this SxS brand new. A couple of years after I bought it, I became disabled. Thus it has only 47 miles and around 16 hours of use. I have no need to keep the SxS. I am in Foley, Alabama. It is very hard for me to get in out of the Challenger. I would like to sell the set, 2019 Challenger 400, trailer and uninstalled winch (this was bought brand new as well, someone was supposed to help this newbie install and we never got around to doing this). I want $6500 for the whole set OBO (Serious offers only).
-
By Xov
Just received delivery of a 2024 AMP Pro. Thought I'd start a thread with my impressions as I use it and learn more. There doesn't seem to be a whole lot of real-world usage information out there on this model. Hope this will help others as they research.
Intended Use Cases
Fire mitigation / slash removal from a 5 acre forested and well-gamble-oaked property. The previous owners thought as much about fire mitigation as I do about fashion: not much. Snow removal Stump pulling General hauling (rock, lumber, etc.) Weimaraner energy depletion. Wasn't an original use case, but a nice added bonus. Experiences So Far
Wasn't impressed that two of the bumpers on the underside of the bed where it sits upon the frame were missing. The metal on metal contact has damaged the powder coating and the frame. I expect a little better QC.
I've only put a few hours on it, so not a ton to report on usage. It isn't quiet; it's silent. I can't even detect an electric note from the motor. I removed (and subsequently replaced) the motor cover noticed that the motor is German and made by Schambuller. The motor controller is Italian and made by Dana TM4. Given the operating specs of both I found on the web, I suspect both are higher quality than the previous Navitas (which is supposed to be decent). The motor is rated at 25 hp and 71.5 lb-ft of torque. It feels very powerful. All the torque is delivered instantly, if desired.
The bed is huge and has an electric dump as standard. Great feature but would like it to go up a bit more. Probably not feasible from an engineering perspective, but I want and I need ;).
Power steering is nice, but vague. Probably common to many UTVs, but I am accustomed to more direct results from input. Plan early and plan often.
In our first full day of usage, we hauled about 1/2 as much slash as the entire rest of the year when I was doing it by hand cart. I may get fatter, but I'll also get more done. After a few days of usage, the battery meter has gone down by 1/10th.
Until next time...
-
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.