Quantcast
Jump to content


Recommended Posts

Posted

Hello all,

I just recently added a dual port USB charger outlet to my Hisun HS400 and thought others might be interested in same:

Got it from Amazon for $13.49. The HS400 has a couple of plugged holes in the dash, left over from prior versions that had the ignition and lighting switches in the dash (these are on the steering column on my 2020 model). The adapter mounts in a 28.5 mm hole so I hogged out the obsolete lighting switch hole (25 mm) with a Dremel tool fitted with a 1/2" sanding drum. I wired it to a permanent power source as it draws very little power (< 5 μA) when not in use--at 5 μAit would take 1.6 million hours (182 years) to drain the battery down to 10 V . It has it's own power switch.

The unit delivered 4.55 V @ 3.0 A with the engine off (12.6 V input) which meets USB specs. The voltmeter displays the system voltage with surprising accuracy-- that's a good value to monitor to reveal battery and/or charging system problems. 

I like it...

the embossed legend is an artifact of the old lighting switch being here

USBPort-00.jpg

  • Like 1
Posted

I was going to do the same thing to mine but found an item on ebay that does the job much easier and cheaper. The item I found plugs into a 12v outlet and has 2 USB ports and also shows voltage . Works great and easy install. I think that it was @  $8.00.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By rdc
      I posted this before , but I had the year wrong. The part I need is for a 2014, I don't know what all years will work, but I need the 2 bearing style with the spacer in the middle. It looks like this pic. If anyone has one I'll buy it rite away. my email is [email protected]. Thanks, RC

    • By rdc
      Hope I posted this in the right place. Looking for the left side shaft carrier where the rear bearings go for an 1100cc sand viper, I understand an 800 cc carrier will also work. I need the old style two bearing with the spacer in the middle, the new style with just the one wide bearing wont work. If anybody has one I'll buy it right away. my email is [email protected]
    • By Burk
      I have a 2021 Axis(Hisun) 700 from Lowes. Will not start. Checked starter, solenoid, spark plug and fuel pump. Everything seems to be fine. The motor turns over and will try to start but just will not. Battery is also good. Frustrated!
    • By HISUN Sector 750 EPS Failu
      "Mrs. Smith" doesn't like how loud our Sector 750 is.  On a HISUN forum someone said the same thing about his 750.  I haven't given it much thought because I've been more focused on stuff that has broken.
      So, I used my decibel meter to check ours out.  4000 RPM, Low gear, under 20 MPH . . . . 97 decibels.  That's above most ordinances, even state boat noise limits.
      AI Overview Ninety-seven (97) decibels is considered very loud and dangerous to hearing with prolonged exposure, roughly equivalent to a newspaper press, a loud nightclub, or a snowmobile. At this level, damage can occur after just 30 minutes, necessitating hearing protection
    • By Hunterman22
      Can anyone please tell me or send a link as to how & where to hook up a code reader to my 2021 Hisun 500 Axis.  I have a 6 pin to a 18 pin  adaptor and the blue cord VAG KKL adaptor .Just not sure where or what to hook up to. Can I use your typical vehicle code reader or do I need to download something on a laptop or PC???
       
×
×
  • Create New...