Quantcast
Jump to content

2015 Hisun Strike 1000 noise

Easyrider

By Easyrider
in Hisun UTV SxS Forum

 Share

Recommended Posts

Easyrider Apprentice

Easyrider

Posted
Posted (edited)

 

 

Can anyone give me an idea what they think this sound could be, I just put new clutch on started it up and heard this sound. Sounds worse when you listen by the air intake.  Any help would be appreciated!

 

 

Edited by Easyrider
Video isn’t showing to hear the problem keeps giving me an error
Link to comment
Share on other sites
ElbowRoom Rookie

ElbowRoom

Posted
Posted

I might know what causes your noise. I got a very similar sound when I removed and re-installed the primary clutch on my 2018 Odes Dominator 1000 (a HISUN relative). There's a plastic washer or spacer that rattles if the clutch bolt isn't torqued enough. Check your HISUN manual for the correct torque. I think mine needs to be torqued to 70 or 75  lbs but I didn't torque it quite enough so it still makes this racket. I might just remove this washer next time I have to remove the clutch because I'm afraid of stripping the bolt if I tighten it more..

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Phil S
      2022 Massimo Buck 450 SxS - Winch Troubleshoot or Replcement Help
      By Phil S
      I have a Massimo Buck 450 and last winter I had the snow plough added by my dealer. After about 15 minutes of ploughing the plough went down but would not lift up. Upon inspection, it appears that the winch is permanently in the free-spool. When you try to wind back in the spool just spins. It is out of warranty and upon looking at replacing I am not sure how I would go about it.
      Has anyone had similar issues?
      Has anyone replaced it with a new winch? is so what model and how was it installed?
      Any help is welcomed.
       
    • Coleman400
      Ut400 gas gauge -not what you think
      By Coleman400
      My gauge is working fine, but as it got low on gas and the gauge showed it as low, I filled it up but the gauge didn't come back up. Does it need to be restarted or anything to reset? Does it need to be driven a certain distance maybe or should it be instant?
    • Greg Kilgore
      Cooling fan. Not just for radiators.
      By Greg Kilgore
      We all know summer is hot inside the cabs of our SXS. So I've rigged up a couple of fans to help cool down the cab.
       
      I didn't want to drill the fan's "support rails" into the ROPS (Roll Over Protection System), aka roll bars. So I used water clamps to hold them in place. 
       
      I just need to replace the wires I ran with bigger gauge. Then finish the wiring to switches, relays, and battery. But the hardest part. The actual mounting of the fans is complete. Also just in case anyone plans on doing this. I may have to only use 1 fan in the middle instead on 2. Due the the draw on the battery.
      The fans are 12", 12V 80W. So I'm figured they were 6.7 amps apiece. Used the WAVe formula to get unknown values Watts=Amps*Volts then solve for unknown. I know the watts and volts from sticker on fan. So just used above formula to get amps. So a 7 amp fuse should be OK and a 10 amp fuse will be good. 
      So pulling 14 amps from the battery all day may be too much for the charging system to keep up with. And I haven't even installed the radio yet. So I will have to test and let you know.
       
      See pics below.

    • Ken Powers
      HISUN STRIKE 550R sound deadening
      By Ken Powers
      I want to use a dynamat sound deadening material to quiet my Strike 550R a bit.  My Q is what about installing the mat to the under side of various body panels? It would be a cleaner look inside.  Would that approach work.
      tia,  Ken
       
    • Sommer Wildes
      New 2021 Tracker 800LE Crew Hot Dash area
      By Sommer Wildes
      TLDR (too long didn't read) in blue for quick scanning
      Hey all! I'm new to the Side-by-side/UTV world. We own a smallish farm and decided to go with the 2021 Tracker 800LE Crew. We like the seating and the ride is smooth. However as a newbie I have some questions that maybe some of you longtime side-by-side/UTV owners can help with. We're still in the "break-in" period and it seems that after 30 min or less of driving the dash area gets super hot. You can feel the heat waves coming off the floorboard by your feet and my phone sitting in the little hole (where a radio might go) felt like I left it in the hot sun for too long. The glovebox was also way too hot. 
       
      So the question is, is this normal, or should I start checking engine coolant and filters? We literal have had it a day. I have read forums and looked up info and can't find anyone mentioning this issue. I just don't want to burn the thing up before we've even put it through it's paces ya know!
       
      Thanks for any help!

  • Gallery Images

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...