Quantcast
Jump to content


PLEASE help me with my 2020 hs500 utv


Recommended Posts

I have replaced the ignition coil, spark plug, injector, fuel filter, map sensor, iac sensor, checked fuel pump and it still acts like it wants to cut out when my revs are over 3100 rpms. the problem is intermittent but happens frequently and i dont want to leave my hisun at a dealer 100 miles away and wait months. It never stalls but it idles rough and sometimes when its real bad i cant go over 10 mph. yes i fasten seat belts

Link to comment
Share on other sites

Just a guess based on a similar problem I had. It seems to be going into limp mode. This is often caused by air in the radiator hoses. If so, raise front end by at least 20 inches, remove rad cap and idle machine until all air bubbles are out while adding coolant. If the problem keeps coming back, there's a coolant leak which needs to be fixed.

Link to comment
Share on other sites

  • 6 months later...

My sister had me check out her 2020 HiSun HS500 UTV.
It never cut out for me because I wore the seat belt.

There is a safety that will make the engine cut-out when the safety-belt isn't fastened.

The way to override this is to wear the seat-belt or to disconnect the sensor wire behind the seat.

Good luck with your machine!

 

Mike H

Meridian, Idaho

Link to comment
Share on other sites

  • 1 year later...

I would like to change the spark plug in my 2020 Hisun 500 HO side by side, thing is I can't find the plug. All the diagrams show a plug and a line, but not where it is. Is it under one of the plates, built into the housing, in the back tire, WHERE. My e mail [email protected]. I am getting mad, the manual is not made for americans to read. 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By Jim Kessell
      2005 American Landmaster
      EH65 Subaru Robins
      spits fuel from breather hose into the air cleaner and then down into carb.  What’s causing this ??
    • By John M in Louisiana
      Quick question about replacing the plug.  One of the prongs pulled out, so I'm thinking it will be an easy fix to connect the old cord with a new plug but I'm unsure about the specs.  15amp 125v?  Is it more complicated than that?  I do plan to buy a plug that's water tight.
      Thanks in advance!
    • By TPlummer
      We recently purchased the Axis x550. Fueled it with 93 fuel and drove one time around the farm and the 02 fault error appeared. Any ideas? 
    • By Kingfish
      The conversion took about 350lbs. off the vehicle.  It never rode great, but now I feel every  crack in the road.  I have backed off spring compression nut to the point just under where they would move around if suspension was at full extension, but it is still very stiff.  I would like to put some softer coilover springs on it, but I have no idea what the spring rate is with the original springs so I would just be guessing on what to order.  Does anyone have the data for the original spring compression rate?  I am willing to give up a little ground clearance for a softer ride. Right now when sitting still the rear suspension is at or near full extension and the rear tires have several degrees of camber which will cause uneven wear if allowed to continue in this state.
    • By 2scoops
      I am in need of an IAC for my throttle body. I contacted JMC and they said I had to buy the whole throttle body for $209. I left a message at Joyner USA...they haven't called back. I found a Chinese company which have them for $17, but shipping is $32. With that I still have to hope it is the correct one which arrives.
      Does anyone happen to have one laying around they would sell?
      I understand a workaround would be to eliminate it and use the idle screw. I believe that would cause problems with cold start ups??? Elevation changes???
×
×
  • Create New...