Quantcast
Jump to content

HiSun Axis 500 Torque Power

Brent

By Brent
in UTV General Discussion

 Share

Recommended Posts

Brent Apprentice

Brent

Posted
Posted

I have a 2021 Axis 500 that I use to launch  my 14 ft Boston Whaler in/out of a watershed lake on a gentle slope primitive landing. The other day as I was pulling it out one of the trailer wheels got stuck. Gave it some gas and still stuck. I put the pedal to floor and the wheels would not even turn with it in Low and 4WD. I would have thought the wheels would at least spin.  Very disappointed in the torque and wish there was away to set the gearing ratio lower.

Link to comment
Share on other sites
Greg Kilgore Collaborator

Greg Kilgore

Posted
Posted

Was on a yamaha forum the other day.

They were talking about adding a shim inside the primary sheave. Supposedly it gave more gettyup on takeoff. But lowered the top end speed.

Also they were talking about changing the spring on the secondary sheave.

 

Maybe something you can research and maybe it can help.

Best of luck.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Mark T
      Can I put a larger engine in my 400 colman UTV ?
      By Mark T
      MY 400 is gutless. I would like to know if I can upgrade to a larger engine ?
    • great8redsfan
      2017 Challenger 500 No power on take off or hills
      By great8redsfan
      Okay folks. I have a low power issue. Been like this for a few years. Place I work at bought 3 and all have lost most of the pulling power.  They gave them away after local shop worked on one for 3 months and it had great power for about 1 month and then crap. They replaced throttle body, fuel injector, spark plug and IAC motor. Seat belt switches have wires cut and left open so no seat belt warning light anymore. It revs to 6k rpm in neutral but when put in gear and take off in low it just doesn’t seem to want to go anymore. Running 93 octane fuel with Stabil.  Any ideas greatly appreciated. I dont have a scan tool but no codes on dash. If held to floor it pops a little and runs almost 5K rpm but if I let off pedal about an inch it smoothed out and revs up to 6k rpm. 
    • Buddee
      2010 500 - New Carb- Hesitation
      By Buddee
      Put a new carb on the 500 to replace the leaking OE one.  Machine idles fine and mid and top end runs great.  It tends to have a hesitation right from the start - bottom end.   Thinking it may be the air/fuel screw??  I didn't do anything with the carb out of the box and is it direct replacement for my machine.  Of interest is the manual choke doesn't seem to work very good now.... wonder is it getting too much air?
       
      Any help appreciated!
       
       
    • Mark M
      2021 Cub Cadet Challenger M550 front cv axle
      By Mark M
      Hello, Hope someone can help driver side cv axle broke anyone know of aftermarket ones you can get, I have 40 Hours on the machine and don't want to pay 450.00 for a new one from cub cadet but I can't find anything after market 
    • buckrub
      trying to finish assembly "new" 2021 Coleman ut 400
      By buckrub
      Hey guys! Newbie here. I'm an old man who's better with plowing a mule (4-legged kind) than these newfangled beasts. I, and a friend of mine, just bought new Coleman sxs and are having to finish the assembly. I've been reading on this site and I'm falling on the mercy of you experts. The only way I'm an expert is that an "ex" is a has been, and a spurt is a drip under pressure. LOL First off, the 2 buggies have no ignition switches. They seem to mount on the dash, not the opening in the steering wheel shaft cover, so we ordered new ones that are supposed to fit. They are 8 inches long, and have a 4-wired white plugin which is slightly rectangled when looking at the end of the plug. The trouble is there's nothing to plug into. There is a three-wire grey plug close enough to reach the four-wire plug, but of course, they are not compatible. 
      Secondly, the blinker, light, ect. unit on steering wheel just spins around when touched. I see no way in heaven or earth to secure it. I've looked at a diagram on the Powersports site, but can't detect how it mounted. Fellows I'd be so grateful for any help with this. Me and my mule will even plow your garden for free, for your help. LOL 
       

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...