Quantcast
Jump to content

18th Annual White Mountain UTV Jamboree


Recommended Posts

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By Rey Ximenes
      OK, here's the mystery of the day. I was using the UTV the other day and the idiot light came on that said it was overheating. I immediately shut down and checked the coolant. No coolant! I refilled the overflow reservoir and the radiator and all was fine. 2 days later the light is on again. I rechecked the radiator and it was again empty? Bone dry? Now, here's the weird part, There is no coolant anywhere on the floor below the vehicle. I can't even see any on the frame. I have it up on the lift and am getting ready to start tearing into the bottom "skid plate" to see if the leak is in the hoses there. Any suggestions as to where to start? I have yet to begin and I am already baffled!
    • By robwork9
      Hopefully someone out there is a T-Boss 410 electrics expert or a Massimo mechanic is viewing this. I parked my 410 and it was working great. I came back a week later and attempted to crank it and nothing. Turned the key and no power. Figured it was a bad/low battery so I charged it. Still nothing. Attempted to jump start it and still nothing. Usually when I put the key in and turn it to the first position, the display comes on and I hear the ECU and other items boot. Now it is doing nothing. 
      I slowly went through the electrical system and found the main fuse attached to the starter relay, part 71602 (pic 1) blown. I figured replacing this fuse would fix my problem. It didn't. I then ordered a new starter relay thinking maybe that part had gone bad and caused the fuse to blow, but a new relay did not fix the problem. 
      I have found a work around for starting the machine. If I take one of the purple/black leads (pic 2) and insert one of them in the bottom right of the starter relay (pic 1 and 3) then the machine will get power even with the key in the off position.  I'm bypassing something but don't know what. I can use my right hand to hold the wire against the lower right of the starter relay, reach over and hold the brake with my foot, then take my left hand and turn the key and it will crank. As soon as I remove the wire from the relay the machine shuts down. I have even removed the power distributor box and it will still get power when I touch the wire to the relay. Of course this is not the way it should work but if I can't solve this problem somehow I may just have to rig a connector to the relay and bypass whatever is causing the electrical issue. Massimo has told me the purple/black wires on my model are not used.
      Any help in figuring what my problem may be or other items I can try?
      v/r,
      Rw
       



    • By jayflight1
      I have a 2011 hisun 800 utv. does anyone have the correct part # for the oil filter. I have ordered 4 off of amazon and ebay and they are the right diameter but are to long
      Thanks
    • By Bill House
      Anyone know of an aftermarket Half Door for the Coleman UTV 400?  Looking for a rigid hinged right and left door with latch...  Thanks!
    • DIY like a pro! Shop from over 1,000,000 Repair Manuals at eManualOnline.com! As low as $14.99 per manual. Shop now.
    • By cliffhodges
      Hi All- Long time reader, first time posting.  I have a 2016 Mule 4010 (model: KAF 620V).  I am having an issue since overloading the payload a couple days ago (yes I'm a dummy).  I live on a very hilly property and I was trying to move some large oak rounds for firewood splitting.  I put WAY too much wood in the bed and when I started driving, it sputtered, kicked out of gear, and then cut out.  I unloaded all the weight and started it again - appeared to be running fine when idling and/or driving on flat ground at slow speed.  But when try to go fast or uphill, the RPM's rev high and it sounds like the motor is fine, but it has ZERO speed or power at all (literally creeps uphill at like 2-3 mph and won' go faster or take any weight), and has no power at all.
      Other info: 3 weeks ago I did a belt replacement.  So I was worried I perhaps screwed that up somehow. But I just opened the clutch housing to check and the belt and clutch appear to be working just fine.... sooo.....
      Any ideas what I screwed up by overloading payload and immediately trying to drive uphill?  Any tips would be greatly appreciated!  
       
       
  • Gallery Images

×
×
  • Create New...