Quantcast
Jump to content

2013 Massimo MSU 500 new primary clutch

Redneck Mech

By Redneck Mech
in Massimo UTV SxS Forum

 Share

Recommended Posts

kenfain Experienced

kenfain

Posted
Posted

Thanks for the clarification. I guess I never thought about it having 2 clutches. My experience with clutches is minimal, at best, and mostly limited to manual clutches on dirt bikes, and the occasional car.

But if it were me, I'd probably give it a very small amount of grease, extremely lightly applied. 

Link to comment
Share on other sites
Redneck Mech Explorer

Redneck Mech

Posted
  • Author
Posted

Of course I googled it and watched a couple of YouTube videos but the info was very conflicting. One guy said it should be assembled dry to keep sand and dust from building up on it. One guy said that it had to be "packed" with grease. And of course varying stages in between. If one of those that know don't reply soon, I guess I'll just put it in the way it was shipped to me and hope for the best.

Link to comment
Share on other sites
kenfain Experienced

kenfain

Posted
Posted

I did the same search, and saw the same conflicting information. I suppose it might be because of subtle differences in the exact types of clutch, and as I said,  I don't know enough to give a definite answer.

That's why I answered as I did. My theory being that a small amount of grease might help, but probably wouldn't hurt anything. And from my experience, gobs of grease, are only used in certain circumstances, and can sometimes do more harm than good. 

So since I don't have any real experience in clutch grease, I really don't know. I only responded out of ignorance, in regard to the vehicle having two clutches. Well that, and to give this worthy question more forum face time, by bringing it to the top.

I'd also like to suggest that you keep us informed about this project, through one of the threads you've started about this machine. We love projects, and pictures. Good documentation might just cause someone else to start their own project. 

Good luck!

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • buckrub
      trying to finish assembly "new" 2021 Coleman ut 400
      By buckrub
      Hey guys! Newbie here. I'm an old man who's better with plowing a mule (4-legged kind) than these newfangled beasts. I, and a friend of mine, just bought new Coleman sxs and are having to finish the assembly. I've been reading on this site and I'm falling on the mercy of you experts. The only way I'm an expert is that an "ex" is a has been, and a spurt is a drip under pressure. LOL First off, the 2 buggies have no ignition switches. They seem to mount on the dash, not the opening in the steering wheel shaft cover, so we ordered new ones that are supposed to fit. They are 8 inches long, and have a 4-wired white plugin which is slightly rectangled when looking at the end of the plug. The trouble is there's nothing to plug into. There is a three-wire grey plug close enough to reach the four-wire plug, but of course, they are not compatible. 
      Secondly, the blinker, light, ect. unit on steering wheel just spins around when touched. I see no way in heaven or earth to secure it. I've looked at a diagram on the Powersports site, but can't detect how it mounted. Fellows I'd be so grateful for any help with this. Me and my mule will even plow your garden for free, for your help. LOL 
       
    • Nathon S.
      Bennche 700 EFI Bighorn New Fuel pump not working
      By Nathon S.
      I have a Bennche 700 EFI Bighorn. I’ve recently been unable to get it to start. After a little troubleshooting I realized my fuel pump was not pumping fuel. This weekend I emptied the gas and replaced it with new. I replaced the fuel pump, fuel filter and fuel injector. I also replaced the battery, spark plug and made sure all my fuses and relays were good. I have confirmed that the float on the fuel pump is not obstructed. The UTV is about 12 years old and has less than 100 hours on it. It has not run in over a year.  Not sure whats going on?!? After doing a little reading I'm leaning towards it being an issue with the ECU or perhaps a faulty wire in the wiring harness. Anyone have any ideas on where to start looking or what I could be dealing with? Any help is appreciated, thanks in advance!
    • aefron88
      The UT400 definitive grease point thread
      By aefron88
      I've seen a number of requests for the location of all the grease points on these machines, and there is no definitive list in the manual. This covers the UT400, but other Coleman/Hisun models should be similar.
      Tools:
      First to grease your machine you need a grease gun and some NLGI#2 grease. You will find it helpful to buy a needle attachment as pictured here, due to poor clearance on some of the U-joints. The rest of the zerks use the standard attachment.
       
      Technique:
      Wipe any dirt/grease off the zerk before greasing to prevent pushing gunk inside and causing excess wear.
      Push the grease gun on the zerk at a straight angle and give it a few pumps. You will hear an oozing noise or sea grease coming out from the outside of the greased area when you've put enough grease in, a few pumps should be plenty.
      If it's just oozing around the zerk you either don't have a good seat with the gun, or the zerk may be rusted and the check ball frozen. Try seating it again and regrease.
      Wipe up any excess grease when youre done to prevent making a mess.
      Greasepoints:



      Rear A-Arms are greasable with the wheels on from the rear, I took the picture with the wheel off for easier visibility

       
      That's it. All other Hisuns should be substantially similar.
    • skittle021
      Super Weird Problem with Primary Shave/Clutch...
      By skittle021
      So I've got a Hisun 550 that I was doing some work on that required removing the CVT and it's housing. Upon attempting to reinstall the clutch, sheaves, etc, I found that the belt no longer fits - it's far too wide. None of the parts have been replaced, they're all OEM. Exactly the same parts as what I took off a few weeks ago.
      To be more specific, my belt is 1.25in wide, but the gap between the clutch and the primary sheave is only 7/8in wide. I'll include a few photos to explain.
      Has anyone ever experienced such a bizarre problem? Any help at all would be appreciated, I've been stuck on this for a month. I'm open to just about any suggestion.
      Photos: 
       





    • LindaCall60
      Need manual for teardown and rebuild 2011 hs 500
      By LindaCall60
      Purchased a 2011 bighorn banchee. Needs motor work. Not sure what. Husband is mechanic but not computer savvy. So, is there a manual that will tell him how to tear this down?  We have down loaded a service manual, but he says it doesn't tell him what he is looking for. 

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...