-
Similar Topics
-
By hetovi
Hey everyone,
I’m in the market for a UTV windshield that can withstand extreme conditions, including high winds, dust, and off-road impacts.
I’ve seen a lot of options out there, but I’m unsure which one will provide the best protection and durability.
Does anyone have experience with windshields that excel in these environments? Are there specific brands or materials you recommend?
I’m particularly interested in options that offer both durability and clarity.
Any tips or personal experiences would be greatly appreciated!
-
By Paul L
When I am driving at 30 to 40 mph on the highway, the display will change from H (high) to R (reverse). It does not actually shift into reverse, it seems to shift into neutral and starts losing speed and the gas pedal has no effect. After the rpm/speed drops for 5 seconds or so, it changes back to H and runs fine for another minute or so. You have to try to drive it at less than 5000 rpm or so, to try and keep this from happening. Any ideas on what the problem might be? It only happens at the higher speeds.
-
By rsar
So I finally got my Quad Gear cab enclosure after waiting out the backorder for three months and to say it's been a huge disappointment is a pretty big understatement. I think mostly because I could make it work, if not for one major issue. The windshield is right next to impossible to see out of. It's a real headscratcher because the side and rear windows are okay. It's not high quality 30 or 40 gauge marine vinyl but I have Quad Gear's stand-alone winshield so I knew it wasn't the best in terms of visibility, but definitely doable for the price. Incredibly, the side and rear windows of the cab eclosure are just as clear as the stand-alone windshield. And the windshield on the enclosure is like 50 percent worse than the stand-alone. It's the same company! I don't get it. If it had just been the rear windshield that was that bad I would have kept it. There are some creases and wrinkles here and there, but I've been using the stand-alone windshield for the past three months so it's good enough not to have to shell out $600 plus for the stock hard windshield. I'd put visibility at about 65- 70 percent. The wife hates it though, which is a pretty big negative. In any case, my original plans were to have an upholsterer change the crappy vinyl out for the high quality stuff and I even sent it to a guy who ended up flaking out on me and refusing to do it. He said he didn't want to charge me $400 for something I paid $200 for. Long story, short, I decided to return it and just get the insanely expensive Kawasaki enclosure next winter since the frigid temps here are about to start climbing in a couple weeks anyway. I first put it on just to see how it would look (I took pics of course) and found that it didnt even seal 100 percent and made it drafty inside the cab. So make that two major issues. At least with the stock enclosure everything will be top flight. Doors will be nice too.
-
By Bryan g
We see a lot of the UT400 with shift problems, not going into gear, popping out of gear, grinding etc. There is a bulletin Im sure everyone has saw about adjusting shift cable. That dont always fix it. I went round n round with coleman on couple units. We are a Coleman warranty repair center"AFS Small Engine Repair " I told them shift lever does not have enough travel . No amount of cable adjustment will increase travel . I extended lever with piece on flat iron by 3/4 of inch . This gave shifter enough travel to properly engage into gear completely . Last couple units to come in for this Coleman sent me a modified shift lever, with longer travel . Problem solved! Also , heads up if you get any new unit ,,,go over and check it out, grease all zerks, check air filter for being in backwards, check wiring harnesses for rubbing on rotating parts, brake hose routing , make sure not touching exhaust . These are just few of the more common failures I see .
-
By downseast
Hi everyone
Recently purchased a 2020 T-Boss 410 in what appears to be good condition
First time with this machine – I also have a diesel Kawasaki Mule which so far seems a better machine
It didn’t start and idle well particularly from cold when I got it and sudden take off ( now solved with new clutch parts ) was all or nothing !
I have replaced the idle valve, throttle position sensor, had the injector professionally checked ( ok) and also the pressure sensor this is a fuel injection engine, also plug and lead etc!
It still doesn’t run well and when starting I have to hold revs for a while as it wont idle but stall, thereafter its better and I have rebooted the ecu which has improved it
When I go to start it clicks as if there is a hydraulic lock and wont return after two or three attempts it then does turn over and start bit I need to give it a bit of throttle to start – is this normal ?
Is there adjustment for the air idle valve ?
The engine seems rough and with vibration compared to other engines I have been used to but some say this is normal?
I haven’t changed the Lambda sensor yet, anyone know how much difference this might make ( I have a new Bosch universal to fit )
Any advice very much appreciated, thanks
-
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.