Bubba

It’s been awhile, did you ever get anything figured out?

That’s cool, didn’t know that, thanks. I didn’t see they mentioned checking the injector but they said they did. I believe they said they got a very good deal on this machine. If so, since they’ve basically checked everything they could, Maybe letting a service dealer take a look???

The hard uppers aren’t cheap around $650 a set and there’s a 2 month back order. I was not able to find any other way to order the sliding glass or solid option but through a dealership. The soft uppers (picture attached) are expensive as well depending on where they’re ordered. Lowe’s has them for $550 a set but Amazon has them from $300 on down to under $100. Personally I don’t consider doors an accessory. Should have came with the machine. I’ll probably machine my own doors and bolt some plexiglass to a metal frame. I’ll just have to open my door to check the mail, lol.

Sounds like an exhaust leak but you said you checked that. I bet you have a clogged fuel injector. Easy to replace if that doesn’t work and since you have checked almost everything, sell it or let a service dealer look at it.

Awesome, later gator!!!

I think but could be wrong but I believe with Hisun the name Stryker & Axis is the only difference. Same machine but Stryker is sold at an authorized dealer/service & Axis is sold by authorized dealer without service like Lowe’s. I’ve heard some call Hisun a Chinese Rhino clone & those parts are commonly known to fit. Your local service dealer can answer all those types of questions. Good luck with whatever you decide, hope I was helpful.

I have a soft top jeep with zippers on the back & rear windows, works fine. My problem with the soft uppers on a Hisun is not only are they ugly but they are way overpriced. I contacted a local authorized brand dealership. They can order or tell you if other models have parts that can fit yours. Surprisingly, the cost of the hard uppers with a sliding window and seal gasket was not much different from the soft doors. I have a 2025 Hisun Axis 750. Hard to find info on hard uppers until I contacted dealer. They come in a solid or sliding window built in. Look awesome not cheap looking, like a dern armored vehicle. I recommend the tinted sliding glass.

Not trying to be smart but I didn’t see anyone mention the simplest thing. Only trying to help but I’ve seen many machines run poorly because the seat belts must be latched, js.

I recommend you contact the brand company & they will tell you the closest dealer/service authorized to make repairs. Even if you’re skilled it’s good to get the repair dealership recommendations. Sure, You can find cheap plug in heaters, butane or propane heaters, under the dash mount heaters from Amazon. You could even go full DIY & get a diesel heater mounted in the bed with dryer vent hoses everywhere. If you want it done right & actually keep your dad warm, a good dealer should recommend a heater that’s tied into the cooling system & is not under but inside the dash. Yes, just like in your truck. Just my opinion but do it right or don’t do it at all & just use blankets & hand warmers.

My son in law had this problem. Turned out to be something as simple as the key fob, lol. He pressed a button or two on it and started right up. Make sure your fob is nearby with good battery. You might have to press a certain button on it. I’d tell you but I haven’t taken my fob out of the glove box in so long I don’t know what buttons are on it. Hope this helps.

I got the same type of connectors pictured from Amazon. 10 of them male and female waterproof to pin connectors for like 13 bucks. I really like how it’s wired in. The tag light only comes on when I turn my lights on.

Sure, maybe it can help someone.

Sorry this is late but I just bought my Axis 750. Maybe I can help someone. There are two accessory pulgs at the rear, near the muffler. Don’t use the obvious two prong connector, use the other four prong. Notice it only has two wires on the back of the plug. Cut the head off the connector and attach your two prong connector. Run your wires to your tag light, that simple. I added an additional male and female connector to the tag light just incase the light gets damaged.